2021+ Bronco ForScan Thread

[Chrome_Pony]

Yeah, hence the manual waterproof inline switch…which isn’t the end of the world.

It is the simple way for sure.

Rather than leave some switching equipment on the Bronco, I've considered playing with an SAE J1772 EV plug and putting the 120V (heaters) on the AC legs and 12V (tender) on the control legs.

Sponsored

 

[rblock50]

Check #13 on the spreadsheet:


Also this thread might be helpful:
https://www.bronco6g.com/forum/threads/rear-12-volt-port-timout.29712/

Personally I wouldn't bother reprogramming, I would simply trace the wire back up to where it gets power (probably under the hood somewhere) and re-route it directly to the battery. If you wanted to be fancy, use a three position switch inline so you could choose whether you wanted to power it straight from the battery for peace of mind when towing, or powered by the circuit so it will have a timeout for battery protection when you're not towing. Just run the original wire to one pole of the switch and the battery wire to the other, then connect the wire going to the power point to the center. Flip it one way and you're on battery power, flip it the other and you're back to OEM operation, make sure you label it correctly LOL

LOL, now I know what that Row #13 was for. I read it as "Power Point", and kept wondering why my Bronco cares about my Power Point presentations. Mystery solved!

 

[Groundhog]

Does anyone know if it is possible to change the speed at which the auto high beams come on? It seems like it is set to 32mph by default, but the speed limits around where I live are only 25mph and it is pitch black at night with millions of deer running around, so I'd like my auto high beams to come on at lower speeds if possible. Thanks in advance for any guidance on this.

Has anyone been able to change the auto high beam speed? Seems absurd they are disabled at 30mph.

 

[GomezK6]

I know this isnt necessarily a FORscan topic but it kinda goes into it. I am using a VCX NANO I can connect to FORscan but I cannot connect to FDRS. FDRS does not allow me to select "different device" option. I was told to call FORscan or contact them in order to get the drivers specifically for the VCX NANO but that doesn't sound right either. Does anyone have any experience using the VCX NANO and FDRS or can help me figure out how to get this thing connected.

 

[mpeugeot]

I know this isnt necessarily a FORscan topic but it kinda goes into it. I am using a VCX NANO I can connect to FORscan but I cannot connect to FDRS. FDRS does not allow me to select "different device" option. I was told to call FORscan or contact them in order to get the drivers specifically for the VCX NANO but that doesn't sound right either. Does anyone have any experience using the VCX NANO and FDRS or can help me figure out how to get this thing connected.

No you should call Ford for support. FDRS is a Ford Motorcraft Software Product... FDRS has been working fine with VXDIAG VCX Nano in the past.

My next suggestion would be to fully uninstall and reinstall FDRS, since you initially installed it without the VXDIAG VCX drivers missing.

 

[GomezK6]

No you should call Ford for support. FDRS is a Ford Motorcraft Software Product... FDRS has been working fine with VXDIAG VCX Nano in the past.

Apologies I meant to say I did call Ford for FDRS support and they were the ones that told me to call/contact FORscan.

 

[BigMeatsBronco]

last statement shows the FAKE....he's fake. there's no way in he'll anyone at FDRS told him to call or contact the folks at forescan...

 

[redone17]

I can’t figure out why I’m still getting the “use parking brake” doo-dee-doo every time I start up.

 

[mpeugeot]

last statement shows the FAKE....he's fake. there's no way in he'll anyone at FDRS told him to call or contact the folks at forescan...

Turns out that he's just unlucky... So there's that. I must admit, it was strange how it all went down.

 

[Lawman]

I want to add 4 blinks to my lane change signal... However, I have different default values than what's listed in the spreadsheet. I don't have either of the 2 default values (didn't modify anything)
Do I just test to see what I get?

Did you ever get an answer for this? I have the same values as you and want to change to 5 blinks!

 

[TheGOAT]

Okay guys, has anyone figured out how to show the forward tire tracks path when using the front camera with the vehicle in Normal mode? Please dont suggest Baja or rock crawl mode, neither are a good alternative.

 

[Sighlense]

What page has a link to the latest (working) forescan link?

 

[35tires]

Do I need forscan to stop the dinging from coming through my speakers when I get in and out of the car or start it? It is SO loud on my stereo it's driving me bonkers.

Any idea?

 

[Rob_Broncowski]

Do I need forscan to stop the dinging from coming through my speakers when I get in and out of the car or start it? It is SO loud on my stereo it's driving me bonkers.

Any idea?

Yes. Turning off all the chimes is one of the best mods you can make with Forscan.

 

[Pacdad]

Can someone with ForScan look at their unmodified AsBuilt APIM for the original “Navigation in Motion” value? APIM Module 7D0-03-01. I am unable to find my original value. I changed the first two numbers to “57” to allow navigation searches during motion and I’m troubleshooting to see if this change (which is great!) caused my electronic “Owners Manual” to be deleted from SYNC “Features” screen.

Sponsored