2021+ Bronco ForScan Thread

[mbdlds]

0100 0001 AB1B after changing position 2 and 4 I get a message saying it's wrong proceed anyway ? I chose yes and the the module changes the code to:
0100 0203 AB1F.

Is that a problem? It does add the modes using the Goat selector. Big Bend mid package, 2.7 V6 auto. Any help is appreciated.

I'm pretty sure I've read here that those are checksums and will change since your changed the other values (ie, nothing to worry about).

Sponsored

 

[BBSas]

Thank you!

 

[SillyPosition]

Is there a way to modify the adaptive cruise control to work in near to 0 traffic speeds?

 

[Tex]

Is there a way to modify the adaptive cruise control to work in near to 0 traffic speeds?

I won't say it's impossible, but my recollection on the matter of ACC is that these are variables that can't really be changed, particularly not with forscan, they're more or less baked into the programming without alterable values. What you're looking for would likely exist in the intelligent cruise control modules, but was left out of ours entirely on all trims and options. I'd love to be able to reduce the minimum distance to about half, but that might also introduce other problems such as the inability of the programming to adjust speed smoothly (ie slamming on the brakes if you're a few feet too close, only to follow up with rapid acceleration to get back to the target distance). My guess is if you did figure out how to change minimum speed, you'd probably run into similar unforeseen issues, potentially impacting safe operation.

 

[willettj]

I read in another thread that the auto start/stop disable via Forscan is not working for 2023 models.. I attempted the change in the Google sheet changing to 00 and it did not work for mine, still need to try to 02 option. the notes for that line are a bit ambiguous.. "Start / Stop: 00=Disabled 01=Enabled, Angle Inhibit Enabled 02=Enabled, Angle Inhibit Disabled" << no code given for the Angle Inhibit Disabled

 

[redone17]

I am trying to enable Rear Defrost on my pre-prep-kit standard package model. I’ve installed the correct harness in the cargo to the hard top. I was successfully able to find, enable and write Rear Defrost in the APIM module, but it keeps giving me a “Service Procedure has been interrupted” when trying to write enabled in HVAC.

Really hoping I don’t need to buy new HVAC controls…as it seems there is a version that comes in all Standard models that looks like this:

When mine looks like this:

 

[willettj]

I am trying to enable Rear Defrost on my pre-prep-kit standard package model. I’ve installed the correct harness in the cargo to the hard top. I was successfully able to find, enable and write Rear Defrost in the APIM module, but it keeps giving me a “Service Procedure has been interrupted” when trying to write enabled in HVAC.

Really hoping I don’t need to buy new HVAC controls…as it seems there is a version that comes in all Standard models that looks like this:

When mine looks like this:

I would bet you are going to have to change that.. I had to buy new switch module to enable my front and rear fog lights

 

[redone17]

I would bet you are going to have to change that.. I had to buy new switch module to enable my front and rear fog lights

How annoying would that be. That version triggers both mirrors and rear. Wiring is in place. Just a pin missing or something?

I can understand the fogs - the buttons don’t exist on the switch. But, this is literally just a different icon.

I’m scared to ask how much they cost…

I’m waiting to hear back from Forscan if there is a Beta that will help. It has in the past…

 

[willettj]

How annoying would that be. That version triggers both mirrors and rear. Wiring is in place. Just a pin missing or something?

I can understand the fogs - the buttons don’t exist on the switch. But, this is literally just a different icon.

I’m scared to ask how much they cost…

I’m waiting to hear back from Forscan if there is a Beta that will help. It has in the past…

If you know the part # take a look at tascaparts.com that's where I got mine

 

[redone17]

If you know the part # take a look at tascaparts.com that's where I got mine

I think I narrowed it down....N2DZ19980L - $350!

 

[Tex]

I am trying to enable Rear Defrost on my pre-prep-kit standard package model. I’ve installed the correct harness in the cargo to the hard top. I was successfully able to find, enable and write Rear Defrost in the APIM module, but it keeps giving me a “Service Procedure has been interrupted” when trying to write enabled in HVAC.

Really hoping I don’t need to buy new HVAC controls…as it seems there is a version that comes in all Standard models that looks like this:

When mine looks like this:

Whoa, hold up...when did the AC controls stop having the digital temp display in them?
I thought that was standard on all trim levels?

 

[redone17]

Whoa, hold up...when did the AC controls stop having the digital temp display in them?
I thought that was standard on all trim levels?

Only for dual temp zones (Mid/High/Lux).

 

[OMTBiker]

Only for dual temp zones (Mid/High/Lux).

2022 did not get the temperature dials on the dual temp packages, chip shortage.

 

[redone17]

2022 did not get the temperature dials on the dual temp packages, chip shortage.

Right. Forgot about that. Not what my original post was about. My image/discussion has nothing to do with HVAC for Mid+. I’m solely discussing the controls for Standard package. Tex just got scared.

 

[Tex]

Tex just got scared.

Not scared, I have mine already. I was surprised to see that they weren't there, that's news to me. Sucks. Good luck with your original post stuff.

Sponsored