2021+ Bronco ForScan Thread

[etmccaus86]

Not sure if the write failures have been resolved publicly yet, but the PSCM process interrupted errors seem to be caused by the module number of some modules not being in the Forscan database. I bought a paid license and he sent me a test version that works.

The current public build works fine with my MY22...

Sponsored

 

[WheelMe]

What are the values present on your vehicle?

I did the EASY config. today on the double-honk, and followed your instructions on cycling the ignition before hitting "OK", it worked - thanks.

The advanced method of changing configuration characters still confounds me - if you recall, my Bronco already shows the value that I'd like to change it to; for example, the turn signal flash times config. for indicating 4 times is to enter an "8" in the second position in the second series of characters (see Litvinup's spreadsheet row below) - the config. that I pulled up from my Bronco already shows an 8 in that position, but it still only flashes 3 times as per factory setting.

Below is the Config. spreadsheet from Litvinup (first image), followed by what I pulled up on my Bronco (2nd image). Since Litvinup's spreadsheet applies foremost to the F-150, I wonder if the Bronco's setting in this regard is different?

SCCM	724-01-01	xxxx	x*xx	xx	0=1 flash, 4=2 flashes, 6=3 flashes, 8=4 flashes, A=5 flashes, C=6 flashes, E=7 flashes ** see SCCM spreadsheet for more options **
** when trailer is connected the truck will add 2 flashes to the above values **

My existing settings:

Thanks for you help.

 

[etmccaus86]

I did the EASY config. today on the double-honk, and followed your instructions on cycling the ignition before hitting "OK", it worked - thanks.

The advanced method of changing configuration characters is still confounds me - if you recall, my Bronco already shows the value that I'd like to change it to; for example, the turn signal flash times config. for indicating 4 times is to enter an "8" in the second position in the second series of characters (see Litvinup's spreadsheet row below) - the config. that I pulled up from my Bronco already shows an 8 in that position, but it still only flashes 3 times as per factory setting.

Below is the Config. spreadsheet from Litvinup (first image), followed by what I pulled up on my Bronco (2nd image). Since Litvinup's spreadsheet applies foremost to the F-150, I wonder if the Bronco's setting in this regard is different?

SCCM	724-01-01	xxxx	x*xx	xx	0=1 flash, 4=2 flashes, 6=3 flashes, 8=4 flashes, A=5 flashes, C=6 flashes, E=7 flashes ** see SCCM spreadsheet for more options **
** when trailer is connected the truck will add 2 flashes to the above values **

My existing settings:

Thanks for you help.

I'm glad it worked out.

That said, the lastest BRONCO-SPECIFIC spreadsheet I've seen on this site has the turn signal count crossed out...as in it doesn't work?

Might/ must be different; just never bothered me enough to dive into it. Maybe someone smarter than me here can.

 

[WheelMe]

I'm glad it worked out.

That said, the lastest BRONCO-SPECIFIC spreadsheet I've seen on this site has the turn signal count crossed out...as in it doesn't work?

Might/ must be different; just never bothered me enough to dive into it. Maybe someone smarter than me here can.

Interesting - can you direct me to that Bronco-specific spreadsheet?

I'm not particularly bothered by 3 vs. 4 flashes, but am just curious as to what's going on. I'd also like to get rid of the DO DO DO chime, but haven't looked into that yet to see if that also has the same issue for me.

Thanks again.

 

[etmccaus86]

It's posted as a sticky in this forum section.

https://www.bronco6g.com/forum/thre...k-sport-mode-chimes-seatbelts-and-more.28489/

I disabled the chimes so you should likely be able to, too.

Also, if you're not backing up your original values before writing anything, you should.

 

[WheelMe]

Thanks for the link - I'll give it a try tomorrow for the chimes.

I did back up my factory settings prior to starting.

 

[Buck₩ild]

Hi,

Does anyone know if the back up camera on standard package be modified to mimic the one from mid package?

As in currently, the grid stays static while a white line is dynamic as opposed to mid package where the back up cam has dynamic grid.

Is this doable and has someone done this?

Bump... Anyone?

 

[jwysopal]

I finally had time to use Forscan on the Bronco, and all changes worked successfully, BUT now throws ABS code which causes “CHECK 4x4” upon startup.

I added Baja Mode, adjusted Tire Size, and disabled double hong. Everything worked, but now stuck with code and comes right back when cleared.

I know I saw a few with same issue in this thread, but they never got a reply with a solution or tip. If you know of a solution, please let me know! Thanks!

 

[Bshull17]

Anyone know if Forscan can disable the DRL low beam on base headlight?

 

[mpeugeot]

I finally had time to use Forscan on the Bronco, and all changes worked successfully, BUT now throws ABS code which causes “CHECK 4x4” upon startup.

I added Baja Mode, adjusted Tire Size, and disabled double hong. Everything worked, but now stuck with code and comes right back when cleared.

I know I saw a few with same issue in this thread, but they never got a reply with a solution or tip. If you know of a solution, please let me know! Thanks!

It's the tire size, make the other modules relearn (especially ABS) and it will clear up the errors.

 

[jwysopal]

It's the tire size, make the other modules relearn (especially ABS) and it will clear up the errors.

thanks! I’ve had ABS relearn multiple times, but no dice. I haven’t tried it with other modules. Maybe I can try that. I thought there was only one main relearn that did everything. Can you have individual modules relearn too? Thanks! If not, I have my stock profile saved, but not sure how to write/load back to a saved profile. Any help is much appreciated!

 

[mpeugeot]

thanks! I’ve had ABS relearn multiple times, but no dice. I haven’t tried it with other modules. Maybe I can try that. I thought there was only one main relearn that did everything. Can you have individual modules relearn too? Thanks! If not, I have my stock profile saved, but not sure how to write/load back to a saved profile. Any help is much appreciated!

It might be the BCM that needs to relearn. Anyway, it happens whenever you change tire sizes.

 

[SevenT]

Has anyone come up with a way to turn of the 'Put your hands on the wheel' warning?

 

[amccue90]

Has anyone come up with a way to turn of the 'Put your hands on the wheel' warning?

I can't recall if I saw that in there. But as straight as my vehicle tracks, the warning is pretty annoying sometimes.

 

[mpeugeot]

Has anyone come up with a way to turn of the 'Put your hands on the wheel' warning?

You don't need FORSCAN to turn that off. I will look it up again.


To switch driver alert on or off, use the touchscreen:

1. Press Features on the touchscreen.
2. Press Driver Assistance.
3. Switch Driver Alert on or off.

Sponsored