What Did You Do To Your Bronco Raptor Today? 🔧 🧰 🪛

[Tye]

I used 2k raptor liner in a spray can with a matte clear. Turned out pretty good.

Do you have a closeup pic you can take? how close is the texture to the bumper texture.

Sponsored

 

[DillonC]

Do you have a closeup pic you can take? how close is the texture to the bumper texture.

I'll take one tomorrow in the daylight. It's not close though. It's a much bigger texture, but still blends in pretty well.

 

[swamp2]

I used 2k raptor liner in a spray can with a matte clear. Turned out pretty good.

Very similar here. Roll on bedliner and 2 component matte clear rattle can. Way too glossy before matte...

 

[Greekbull]

ADD Phantom bumper and some new lights

That looks great! I've been going back and forth with the idea of the Phantom or Bomber from ADD of the Maxlider bumper so I can add a winch. Plan to do a lot of off-roading and don't not sure about rolling without the winch.

 

[Chieftain]

That looks great! I've been going back and forth with the idea of the Phantom or Bomber from ADD of the Maxlider bumper so I can add a winch. Plan to do a lot of off-roading and don't not sure about rolling without the winch.

Thanks! I like the low profile look of the Phantom. Consider the ADD Rock Fighter. It has less going on than the Maxlider, still has recovery points, and you can get a front camera relocation kit from DV8 I think so your winch won’t obstruct the front camera.

 

[Greekbull]

Thanks! I like the low profile look of the Phantom. Consider the ADD Rock Fighter. It has less going on than the Maxlider, still has recovery points, and you can get a front camera relocation kit from DV8 I think so your winch won’t obstruct the front camera.

Thanks, love most of the ADD bumpers but I'm not a fan of the Rock Fighter. The winch sits way to far up high for my liking. That's one of the things I like most about the Maxlider look is the winch sits down low and it's still made by ADD.

I think I'm going to try and likely do the Maxlider and mod the internal brackets to fit Baja Designs Squadrons.

 

[Chieftain]

Thanks, love most of the ADD bumpers but I'm not a fan of the Rock Fighter. The winch sits way to far up high for my liking. That's one of the things I like most about the Maxlider look is the winch sits down low and it's still made by ADD.

Fair point. It’s a mean looking bumper and fitting to the BRaptor. I just read that you can keep or remove the brush guard too if you ever opted for a different look.

 

[swamp2]

1st wash (4 months). SunTek PPF did wonders entirely eliminating desert pinstripes. They would have been plentiful sans PPF.

 

[Johnny Mo]

Started mounting my tube doors to see how many shims they will need. Seems like front 2 already had a few in there but fit good with exception of tweaking the bumper near the latch a bit.

 

[timbal1963]

Needed a good washing!

 

[350vudu]

Finished the projects I was working on and got all my gear loaded for camping at Bronco Super Celebration tomorrow.

-air lines ran to each wheel well
- American adventure labs cargo floor, battery mount, fridge slide and compressor mount
- dual battery system

 

[DillonC]

Do you have a closeup pic you can take? how close is the texture to the bumper texture.

Here's a close up. Like I said it's not really close to the factory bumper texture, it all blends in pretty well when looking at the whole front end though.

 

[DillonC]

Over the last couple days I cleaned it up really good and applied Adam's advanced graphene ceramic coating to the whole vehicle. Left it in my shop for a couple days to cure and just now pulled it outside for the first time.

Hard to drive and get it dirty when it looks this good clean lol.

 

[swamp2]

Mabett Rear Cup Holder and Quadratec (longer) Spare Wheel Bump Stops

Full details on my build thread.

 

[BROGAN]

So I added some decals to the Raptor emblem. I think it really makes it pop. Couldn't really make out the logo before unless you are right up close. I was thinking about pulling the trigger on the decals for the front FORD letters. Thoughts? Has anyone done this, and how do you like it?

Sponsored