Rock Jock Track bar relocation bracket is totally worth it!

[NJNMDoc]

As the title says- I just wanted to let everyone know that the Rock Jock Track bar relocation bracket is totally worth it!

Well worth the $100 if you have any type of lift. It helps to correct the rear geometry which helps trim out the bounce/sway and improves handling.

Great work RockJock!

https://www.rockjock4x4.com/RJ-181400-101

Sponsored

 

[derichio02]

As the title says- I just wanted to let everyone know that the Rock Jock Track bar relocation bracket is totally worth it!

Well worth the $100 if you have any type of lift. It helps to correct the rear geometry which helps trim out the bounce/sway and improves handling.

Great work RockJock!

https://www.rockjock4x4.com/RJ-181400-101

Did you install yourself? And notes or videos?

 

[NJNMDoc]

Did you install yourself? And notes or videos?

Ya- it was a cake walk!

Install PDF online was simple to understand. Whole deal took about an hour.

Air tools will help, but have a breaking bar at minimum and a torque wrench capable of 180ftlbs and you’re good to go.

Use a ratchet strap to pull the body to the left when re-aligning the bolt holes. Super straightforward and well worth it!

 

[derichio02]

Ya- it was a cake walk!

Install PDF online was simple to understand. Whole deal took about an hour.

Air tools will help, but have a breaking bar at minimum and a torque wrench capable of 180ftlbs and you’re good to go.

Use a ratchet strap to pull the body to the left when re-aligning the bolt holes. Super straightforward and well worth it!

Nice! Is an alignment needed after this change? I just went with RPG 2.25/2.25 and got about 1 3/4” lift and it has already been aligned.

 

[NJNMDoc]

Nope- I was in the same shoes (post RPG)... alignment was not impacted as far as I can tell. RockJock tech said as much as well.

 

[derichio02]

Nope- I was in the same shoes (post RPG)... alignment was not impacted as far as I can tell. RockJock tech said as much as well.

I looked but couldn't find the HOSS 3.0 shock length. It says on their site minimum length is 18.15. Are the HOSS 3.0 coilovers long enough? Not sure if you had a chat with the tech and got info

• Shocks - 18.15 in. minimum rear shock length at full compression (otherwise bracket can collide with the frame).

 

[NJNMDoc]

I looked but couldn't find the HOSS 3.0 shock length. It says on their site minimum length is 18.15. Are the HOSS 3.0 coilovers long enough? Not sure if you had a chat with the tech and got info

• Shocks - 18.15 in. minimum rear shock length at full compression (otherwise bracket can collide with the frame).

Interesting. I haven’t had any clearance concerns and yes I talked with the tech. He cleared it for my setup.

The install PDF was on their website (blue font link). I’ll take a look for it.

 

[NJNMDoc]

OK- found the link for you on their page under instruction manuals:

https://www.rockjock4x4.com/ford-bronco-data

 

[mrandol]

Is this product for the Braptor? It’s marked for the Braptor forum but I don’t believe it was designed for Braptor.

 

[NJNMDoc]

Is this product for the Braptor? It’s marked for the Braptor forum but I don’t believe it was designed for Braptor.

Ah apologies- I think it’s in the wrong section. Maybe the mods can move it.

 

[mrandol]

Ah apologies- I think it’s in the wrong section. Maybe the mods can move it.

No worries, I was just confused.

 

[BUCKIN6VA]

Ya- it was a cake walk!

Install PDF online was simple to understand. Whole deal took about an hour.

Air tools will help, but have a breaking bar at minimum and a torque wrench capable of 180ftlbs and you’re good to go.

Use a ratchet strap to pull the body to the left when re-aligning the bolt holes. Super straightforward and well worth it!

Getting ready to install mine today. Did you even need to jack up the rear end?

 

[Oldhippie]

Ya may be able to move axle to line up the bolts on the ground but I would like to get the tension off the ground

 

[NJNMDoc]

Getting ready to install mine today. Did you even need to jack up the rear end?

Nope.

 

[Ramble_Offroad]

Now that these have been in market for a bit are you guys still happy with this adaptor?

Any reason this adaptor would not be a good fit with my kit? Sounds like it can’t hurt to give it a try.
- Fox 2.5’s with Eibach 3.75” coils
- stock track bar
- etc.

Sponsored