Installed IAG 4PC Interior LED Dome Light Kit with Harness

[Wildfire1]

Had to remove parts of the roof rack, forward and mid section of the top but it went well. Took almost 3 hours but it’s a great quality kit and made a Hugh differance to the lighting of the interior. Still waiting on the Mabett rear dome light to get here and then that should do it for lighting. Thanks @IAG Performance for offering this great kit.

Sponsored

 

[Area51BS]

Where did you get the 4 door toy in hood?

 

[Area51BS]

I’m sold. Ordering the light kit.

 

[Beach_Bum]

Can the lights be installed in the rear and forgo the front lights?

 

[Wildfire1]

Where did you get the 4 door toy in hood?

That’s a Traxxas 1/18 scale rc Bronco. It has the optional Area 51 body. We did the graphics last evening to match our actual 2022 bronco.
i‘m also doing a 1/10 scale bronco with lift kit, wheels and tires………. It’s a fun hobby. You can get them at most hobby shops

 

[Wildfire1]

Can the lights be installed in the rear and forgo the front lights?

I don’t see why not. I never tried that but I’m sure it’s very doable.

 

[4x4TruckLEDs.com]

I’m sold. Ordering the light kit.

We've got them in stock: https://www.4x4truckleds.com/iag-4-piece-interior-led-dome-light-kit-w-harness-for-2021-ford-bronco/

 

[Beach_Bum]

That’s a Traxxas 1/18 scale rc Bronco. It has the optional Area 51 body. We did the graphics last evening to match our actual 2022 bronco.
i‘m also doing a 1/10 scale bronco with lift kit, wheels and tires………. It’s a fun hobby. You can get them at most hobby shops

@GToddC5

 

[JediMcMuffin]

Well done, I too am probably also going to get the Mabett one. I am inclined to put red film over the IAG one and control it only via aux switch.

 

[Wildfire1]

We've got them in stock: https://www.4x4truckleds.com/iag-4-piece-interior-led-dome-light-kit-w-harness-for-2021-ford-bronco/

I paid $129.99 for the 4 door hard top set with the required brackets.

 

[helifino16]

Can the lights be installed in the rear and forgo the front lights?

The wiring harness that it conveniently comes with is only long enough to reach the front and mid positions on the Roll bar. You would just have to doctor that up to move the lights further back.

 

[Beach_Bum]

The wiring harness that it conveniently comes with is only long enough to reach the front and mid positions on the Roll bar. You would just have to doctor that up to move the lights further back.

I was thinking for the 2-dr and just have the rears installed. They look really bright and I don't want be blinded with a light on the peripheral of my eyes. I just wasn't sure if the harness was capable of having just 2 of the lights.

 

[helifino16]

I was thinking for the 2-dr and just have the rears installed. They look really bright and I don't want be blinded with a light on the peripheral of my eyes. I just wasn't sure if the harness was capable of having just 2 of the lights.

I'm sure you can just leave off the fronts. IAG would have to verify that making the rear lights work is dependent upon having the front connected. Or someone installing these can verify by unplugging one (or both) of the front ones.

 

[ATLBronco75]

I installed mine last weekend too. They are extremely bright. My wife complained about the glare. I might look at some kind of softening filter for them. I have mine connected to the dome light circuit and Aux 6.

 

[Wheeljack]

Just installed these last night. Took a couple of hours but it's well worth it with how dark the Bronco interior is. Hardest part was dealing with the wire harness since ford doesn't give you a lot of room to work with.

Sponsored