ARB Differential Cover, 12-bolt, Nodular Iron, Red Powdercoated, Dana M220, Each For 2021-2024 Ford Bronco 750012

[ticklemybronco]

ARB Differential Cover, 12-bolt, Nodular Iron, Red Powdercoated, Dana M220, Each For 2021-2024 Ford Bronco 750012

Available here : https://ticklemybronco.com/products/ab-fb-arb-750012-t14-1

Extra discount using AN5 code

When off-road, encountering obstacles and hazards that could inflict expensive damage to your differential is inevitable. ARB differential covers are made from high-tensile strength nodular iron (tougher and harder than carbon steel); they are engineered to protect the differential and ring and pinion from off-road hazards. Available for a select line of differentials, they are offered in red or black powdercoated finishes.



Features of ARB differential covers include:



* Computer-optimized, cross brace design increases the structural rigidity of the entire axle

* Helps keep the ring and pinion gears meshing on the flat faces of the teeth--greatly increasing ring and pinion life and overall strength

* Top-quality, rare earth magnets on both the drain plug and dipstick collect metallic particles

* Dipstick magnet allows the oil to be checked for tell-tale signs of internal damage

* Prolonged carrier bearing life (especially on high-output vehicles) from improved support of bearing alignment

* Approach/departure angles optimized by angled exterior surfaces that minimize hang-ups

* Unique dipstick/filler cap design allows differential oil level to be adjusted for rotated differential housings

* Low-profile drain plug resists damage from obstacles

* High-strength cap screws (included) are recessed into the cover for impact protection



Cover Bolts:12

Ring Gear Bolts:10

Cover Material:Nodular iron

Cover Color:Red powdercoated

Filler Plug Included:Yes

Drain Plug Included:Yes

Carrier Main Cap Support:No

Gaskets Included:No

Bolts/Studs Included:Yes

Quantity:Sold individually.



Fitment: 2021-2024 Ford Bronco

Sponsored

 

[Wildfire1]

Will this fit a ‘22 Sasquatch option?

 

[ksdon]

Is there a pre-made gasket for this cover? I never seem to made a leak free gasket if I have to use goop from a tube to make one.

 

[Felix808]

Is there a pre-made gasket for this cover? I never seem to made a leak free gasket if I have to use goop from a tube to make one.

The factory ones is reusable if you don't gouge it.

 

[Tricky Mike]

Is there a pre-made gasket for this cover? I never seem to made a leak free gasket if I have to use goop from a tube to make one.

Have you tried Ultra Black? It's always worked perfectly for me. I do a small bead, hand tighten, let set a day, then torque.

 

[ksdon]

The factory gasket is a good one! Is it known that the factory fits this cover? I ask because the ARB cover looks to be a little smaller than the factory. At least some pics.

 

[Tricky Mike]

The factory gasket is a good one! Is it known that the factory fits this cover? I ask because the ARB cover looks to be a little smaller than the factory. At least some pics.

That's not even a D44/M220 in that pic. Here's one on a Bronco.

 

[Glade Runner]

Should have been eruption green instead of red…

 

[Felix808]

The factory gasket is a good one! Is it known that the factory fits this cover? I ask because the ARB cover looks to be a little smaller than the factory. At least some pics.

Proven by my real world experience

And yes as @Tricky Mike stated this is not the M220 cover shown by the OP, but just a stock photo I'm assuming.


Pics of mine installed:

 

[Sparkherd]

Any idee what size brake line adel clamps those are?
I'm about to change mine out and I dunt wanna make an extra trip!

 

[Fordified1]

Can someone clarify which Broncos have the M220 differential?

 

[Ducati1098]

Can someone clarify which Broncos have the M220 differential?

All of them except Raptor.

 

[Felix808]

Any idee what size brake line adel clamps those are?
I'm about to change mine out and I dunt wanna make an extra trip!

I used 1/4", but would have gone larger so I didn't have to cut the sheathing. I like you didn't want to make an extra trip so cut it was

 

[Sparkherd]

I used 1/4", but would have gone larger so I didn't have to cut the sheathing. I like you didn't want to make an extra trip so cut it was

Thanx Marine!

Sponsored