Mohave Custom Designs rollbar StarLink Mount

[Run3gun]

https://mohavecustomdesign.com/prod...-roll-bar-mount-for-ford-bronco-4-door-raptor

Sponsored

 

[Ape Factory]

I think there are a few threads on this already. Installed one about a month ago. Good product.

 

[mohavecustom]

Thanks for the shout out! We have mounts for Bronco Raptor, 4-doors, 2-doors, soft-tops, and a dash mount now too.

Appreciate all the support we have gotten from Bronco6g

 

[Tye]

Question, why does it angle the Starlink vs making it parallel to the roof? Does that help with signal or ?

 

[popo_patty]

Question, why does it angle the Starlink vs making it parallel to the roof? Does that help with signal or ?

Starlinks prefer to be angled

 

[Run3gun]

I think there are a few threads on this already. Installed one about a month ago. Good product.

Just sharing my Journey !

Question, why does it angle the Starlink vs making it parallel to the roof? Does that help with signal or ?

Started it up in the driveway and connected immediately so the angle is doing the trick !

 

[mohavecustom]

Starlinks prefer to be angled

Started it up in the driveway and connected immediately so the angle is doing the trick !

Not a lot of room back there to play with, especially with a soft top moving around. Lots of trial and error, trust me!

 

[maliu]

I have been looking for a mount like this for awhile. My early review. Got it a few days ago. When I ordered it wouldn’t let me choose a non Raptor. I sent a message and they responded very quickly and told me to place the order and they would ensure I got the bolts which was the only difference. Raptor no bolts/Others bolts. Installed in minutes. I forget the mini is in the rig. It tucks right up under the roof. When I have power to the mini it connects quickly. Only issue is non mount related. My DC adapter works on and off (works great with my power station). Ordered the Starlink one. No rattles. 3D printed item so finish is as expected. I would expect fewer sharp edges if it was a molded plastic. End result: Would I buy again? 100% so far. I rarely write reviews but I love this!

 

[Rambo30BL]

Started it up in the driveway and connected immediately so the angle is doing the trick !

Does your dish touch the metal frame of the soft top? I just installed mine and noticed it hits the frame. With a little encouragement the soft top locks but it is right against the dish. I'm looking at buying a dish cover to get rid of any rattles and possible wear

 

[Run3gun]

I have been looking for a mount like this for awhile. My early review. Got it a few days ago. When I ordered it wouldn’t let me choose a non Raptor. I sent a message and they responded very quickly and told me to place the order and they would ensure I got the bolts which was the only difference. Raptor no bolts/Others bolts. Installed in minutes. I forget the mini is in the rig. It tucks right up under the roof. When I have power to the mini it connects quickly. Only issue is non mount related. My DC adapter works on and off (works great with my power station). Ordered the Starlink one. No rattles. 3D printed item so finish is as expected. I would expect fewer sharp edges if it was a molded plastic. End result: Would I buy again? 100% so far. I rarely write reviews but I love this!

I use a 12v to StarLink connector and plug in to the 12v cig port directly below works great everytime

 

[Run3gun]

Does your dish touch the metal frame of the soft top? I just installed mine and noticed it hits the frame. With a little encouragement the soft top locks but it is right against the dish. I'm looking at buying a dish cover to get rid of any rattles and possible wear

It did not I have since swapped out the soft top for hard top

Sponsored