Fire Extinguisher Mounted Pics - Post Em!

[B Miller]

B Miller can verify, but I would think type A would cover most of your interior, as well as brush or anything else that catches fire outside the vehicle...

This is correct. The "A" in ABC covers common combustible materials, such as wood, paper, or most plastics.

We carry a 20 pound ABC dry chemical in the fire engine. On a car fire, we start with water and foam. If it's a stubborn fire we use the dry chemical.

We don't start with the dry chemical because after it's used, we have to send it out to be re charged. Most of the time water and foam does the trick.

Sponsored

 

[mtap]

Went with a cheap mount on amazon…holes didn’t line up perfectly so I used a hose clamp wrapped with electric tape and also lined the roll bar with Velcro for the bottom …pretty solid.
You can use existing bolt for the top hole (the one that secures your MIC-same thread pattern).

 

[Tricky Dick]

Finished my seat handle bracket for the Amazon quick release. Needs some paint then I can install.

 

[Stick355]

Atomic Monkey Industries

Bought the one for a Ranger, they didn’t have a Bronco specific one at that time.

 

[Tricky Dick]

Done.

 

[KDoug866]

 

[Jpursuit]

I have an Element Extinguisher on the molle driver's seat panel. Was looking at regular units but just felt these were better and easier to mount and based on what I've seen they seem to work the same if not better so... that's what I went with.

Bought one of these for each vehicle as well. Thanks for posting the way you mounted it. I've been looking for a convenient yet out of the way spot for this.

 

[SoCalG]

Hi. Great setup! Who makes those panels and that storage area cover? Is this a 2 door or 4 door? Thanks

 

[KDoug866]

Hi. Great setup! Who makes those panels and that storage area cover? Is this a 2 door or 4 door? Thanks

Thanks, My Bronco is a WildTrak 4dr.

Texas Complete makes the side panels, link below
https://www.texascompletebronco.com/products/2021-bronco-rear-molle-panel-4-door
The rear enclosure is made by Ford Accessories, link below also.

https://accessories.ford.com/products/bronco-4dr-2021-deluxe-raised-lid-cargo-area-enclosure-1

 

[ChompSticks]

Done.

You made that yourself? Are you able to move the seat easily? Mine is mounted down low but I have to be careful not to push the seat all the way forward. (My seat is all the way back here, handle isn't in the way in driving position)

 

[Tricky Dick]

You made that yourself? Are you able to move the seat easily? Mine is mounted down low but I have to be careful not to push the seat all the way forward. (My seat is all the way back here, handle isn't in the way in driving position)

I've been known to do a little fabricating from time to time. I have to pull the extinguisher to slide the seat, but I've never had to do that once I got it set where I wanted.

 

[604Bronco]

I've been known to do a little fabricating from time to time. I have to pull the extinguisher to slide the seat, but I've never had to do that once I got it set where I wanted.

Better said: The fire extinguisher stops others from screwing with your seat.

 

[Hemisfear]

We were looking at making a mount for these threaded holes. We stopped when we noticed our Badlands didn’t have those provisions but our wildtrak did.

My '21 Badlands has the bar holes!

 

[JcrOffroad]

My '21 Badlands has the bar holes!

Prototype.

 

[ChompSticks]

I've been known to do a little fabricating from time to time. I have to pull the extinguisher to slide the seat, but I've never had to do that once I got it set where I wanted.

Ahh poo. That would be no slice for us then. Love it though! If I were single it would be perfect!

Sponsored