mObridge dsp/amp ***DSP configuring***

[Lowellbarton]

Anyone have a similar setup as mine with a good map file?
In all my excitement, I've overwritten the stock file.

what I'm using:
3 - 4" KSC40's in dash
2 - 6.5 KSC650's in the kick panels
2 - 6.75 KSC6704's in the rear pods
1 - CompR 8" in stock sub enclosure
All Kicker brand

Sponsored

 

[ssqch]

Has anyone got Fraser's file, the 4 presets, that comes with the amp for his setup? Somehow mine got erased when I did the firmware update a few days ago. Thanks!

 

[jabrax]

I think Fraser's file is custom starting file for your setup. If you are in a crunch you can get the base bronco file from the support tab at the bottom of the product page. It doesn't sound as good, but it will get it running again. I had mishap earlier and my file wiped.

 

[BlarneyStoned]

You can download the base tune from https://community.mobridge.us/api/download_tune?tune_id=20

 

[ssqch]

It's a .rax file. How do you open it on iOS?

 

[jabrax]

It's a .rax file. How do you open it on iOS?

Open it with the Mobridge app. I created a file called Mobridge Tunes and leave my versions there.

<file> <open new tune>

Whenever I make changes I "save as" a new name to also keep the original
If you want to see it while not connected to the car - select "enable offline editing" near center of the screen

 

[Chritaka]

I'm running all Hertz Cento line... CX100 4" in dash corners, CX165 in rear Mabett pods, PRV 4" neodymium mid in center channel, Hertz 165L in the kicks. I'll be doing the JL Audio stealthbox as well. I was messaging with Mobridge on IG and he said they have a tune already for this setup.

Is there any way to flash the amp prior to install? Can Fraser do it before shipping? I asked the same via IG and will update when I get a response.

 

[BigJ2]

Good questions. Fraser has been pretty responsive. I’m getting it dialed in, but it’s not to its full potential and I can easily hear it. At any rate, I may have to take it into the pros with a mic and such.

 

[jabrax]

I'm running all Hertz Cento line... CX100 4" in dash corners, CX165 in rear Mabett pods, PRV 4" neodymium mid in center channel, Hertz 165L in the kicks. I'll be doing the JL Audio stealthbox as well. I was messaging with Mobridge on IG and he said they have a tune already for this setup.

Is there any way to flash the amp prior to install? Can Fraser do it before shipping? I asked the same via IG and will update when I get a response.

The tune will come loaded on the amp

 

[Chritaka]

The tune will come loaded on the amp

Only if you email them or send a msg with your setup. I sent Fraser a msg in IG and also replied to the order email with my config. He said he’d preloaded the tune for my setup. Just need to get the time to install everything!

 

[Hemisfear]

I'm running all Hertz Cento line... CX100 4" in dash corners, CX165 in rear Mabett pods, PRV 4" neodymium mid in center channel, Hertz 165L in the kicks. I'll be doing the JL Audio stealthbox as well. I was messaging with Mobridge on IG and he said they have a tune already for this setup.

Is there any way to flash the amp prior to install? Can Fraser do it before shipping? I asked the same via IG and will update when I get a response.

I have a similar set up I'm currently working on installing, 4xCX100, C165L & JL8w1v2 in the factory enclosure, what can you tell me about the PRV 4" mid/centre channel and how does it interact with the CX100's you installed?

 

[Chritaka]

I have a similar set up I'm currently working on installing, 4xCX100, C165L & JL8w1v2 in the factory enclosure, what can you tell me about the PRV 4" mid/centre channel and how does it interact with the CX100's you installed?

It’s ok, fills the need. It seems a little harsh at times. I’ll replace with Hertz or Morel at some point I think, so they’re all matched.

 

[Hemisfear]

It’s ok, fills the need. It seems a little harsh at times. I’ll replace with Hertz or Morel at some point I think, so they’re all matched.

Thank you...l
I think I may wait to do something with the centre channel once I have everything up and running (I have the speakers installed, but still runninmg on the B&O). If I decide the 4" in the rear won't work for my taste, I will use one of the CX100's as a centre channel, tuning out the tweeter and go with the larger rear pods, I'm just concerned that the boxes look a bit tiny for a 6-1/2" speaker, sort of defeats the purpose of going larger!

 

[Chritaka]

Thank you...l
I think I may wait to do something with the centre channel once I have everything up and running (I have the speakers installed, but still runninmg on the B&O). If I decide the 4" in the rear won't work for my taste, I will use one of the CX100's as a centre channel, tuning out the tweeter and go with the larger rear pods, I'm just concerned that the boxes look a bit tiny for a 6-1/2" speaker, sort of defeats the purpose of going larger!

You're welcome and sounds good. Note that I had a noticeable difference with upgrading to 6.5" with Mabett rear pods on my B&O, esp. with the mid bass, but the 4" may fill enough for you once you have it all in place. I covered the inside of the pods with Kilmat and added poly also.

I was also looking here at some of their single mid bass woofer options for the center, particularly their FaitalPro 4FE32 and the Morel 424D Shallow 4".

 

[baskethead]

Ive just finished installing everything and was wondering if anyone has a rax file with a similar setup to get started?
thx
Greg
AF GB15
AF GB60
AF GS 42 (center)
AF GS62 (rears)
JL stealthbox sub

Sponsored