What did you do TO / WITH your Bronco today? 👨🏻‍🔧🧰🚿🛠

[TPadden72]

Never good to sneak around on the wife…

Not a problem if you don't get caught..

Three months after I traded a motorcycle my wife said I thought your BMW was green, I said no it 's blue. She never caught on...

Tom

Sponsored

 

[Scooter M'Gee]

Installed the Burger Motorsport intake lid and grey dry filter. This was on a 2025 2.3L. Fits like a glove.

https://burgertuning.com/products/bms-cold-air-intake-for-ford-bronco?variant=47624647934126

 

[chopperbobby]

Ordered some 34" K02's for my wife's Bronco. Stock is 33". Im going to sneak up 1" every time I replace the tires so she doesn't notice. I'll also do a slight 1" body lift when she's not looking. If she says something about it getting harder to reach the door I'll just tell her shes getting old and shrinking.
This is kind of the same way my gun safe works

Think my plan will work?

 

[BeerRunner]

brother in law got married - did this to his bronco in San Antonio

 

[5GENIDN]

Ordered some 34" K02's for my wife's Bronco. Stock is 33". Im going to sneak up 1" every time I replace the tires so she doesn't notice. I'll also do a slight 1" body lift when she's not looking. If she says something about it getting harder to reach the door I'll just tell her shes getting old and shrinking.


Think my plan will work?

But honey... It really is not that big... We can make this work....

And now she enjoys it....

 

[5GENIDN]

Very misogynistic way of saying sister got married - did this to their Bronco.

Tom

Unless of course this was his wife's brother?

 

[TrailDamage]

Well I am making the Bronco into more of a full time use daily driver so I installed a phone mount. Haven’t been satisfied with many options but I have used Off Roam in the past so I stuck with them and got their MagSafe charging mount. Unfortunately the mount as it comes keeps the phone right over the screen. I added their longest available arm to offset it to the left and it helps put it nearly over the vent area. Could be a little longer but this works for now. Still need to work on a neater power cord solution but this works for now. Pretty sturdy so far.

 

[Fastmc25]

Ordered some 34" K02's for my wife's Bronco. Stock is 33". Im going to sneak up 1" every time I replace the tires so she doesn't notice. I'll also do a slight 1" body lift when she's not looking. If she says something about it getting harder to reach the door I'll just tell her shes getting old and shrinking.


Think my plan will work?

Mine had difficulty getting in all the time. So….. i added running boards. Then a 2” lift and my wife hasn’t said a peep . So far so good

 

[chopperbobby]

Too much Sasquatch

 

[jayr1959]

Got the compressor wired up.

 

[JL8jeff]

I swapped out my original driver's seat cloth cover/cushion for a used one I grabbed on Ebay. I have RC seat covers to protect the seats but with the lift and 37's you have to slide out of the seat and I figured it would eventually damage the cushion and probably the stock cloth seat cover. My original seat cover/cushion only has around 9200 miles on it so it was worth setting it aside to keep in new condition. My fingers are sore from trying to pry the cover off the seat frame but I was successful and had no injuries or blood from scratched knuckles.

Here's the cleaned up Ebay cover/cushion:

 

[Jazer]

Never good to sneak around on the wife…

As a wife, I would be 100% ok with that type of sneakies.

 

[TX-Dennis]

Installed some cheapo amazon hood struts. They work well, and were easy to install (less than half an hour). I cannot speak to their longevity at this point, though.

The manufacturer says they are stock height, but they actually open quite a bit higher than the stock prop rod.

https://www.amazon.com/dp/B09W4HRH2P?ref=ppx_yo2ov_dt_b_fed_asin_title&th=1

 

[logan112]

I agree with you on the capable bumper..... I really like some of the others but there is not one I would rather have....

Love the look of this with the winch hidden. What’s the difference between a capable bumper and modular bumper.

Hoping to replicate this on my 2026 Bronco OBX.

 

[random_buffalo]

About 3’ deep I. The middle. Little anxiety along the way.

Sponsored