You use the same kit as the 4 door, you just have to find a place to mount the amp.
You use everything except the supplied mounting plate.
Talk to Fraser, maybe he can put something together for you!
Sponsored
Sponsored
B&O Stereo System Upgrade on 2025 Bronco Raptor
- Thread starter Hoytadickes
- Start date
- Watchers 33
You use everything except the supplied mounting plate.
Talk to Fraser, maybe he can put something together for you!
OP
OP
- First Name
- Hoyt
- Joined
- Dec 29, 2025
- Threads
- 2
- Messages
- 43
- Reaction score
- 95
- Location
- Chesapeake, VA
- Vehicle(s)
- 2025 Bronco Raptor
- Your Bronco Model
- Raptor
- Thread starter
- #47
Yep that's the one
- First Name
- Chris
- Joined
- Jul 19, 2025
- Threads
- 0
- Messages
- 4
- Reaction score
- 0
- Location
- Pittsburgh,PA
- Vehicle(s)
- 2024 BRaptor
- Your Bronco Model
- Raptor
What speakers did you use for the rear pods? Mine rattle like crazy and if I make any effort to polyfill, I'll swap them out to something better. Thanks!
OP
OP
- First Name
- Hoyt
- Joined
- Dec 29, 2025
- Threads
- 2
- Messages
- 43
- Reaction score
- 95
- Location
- Chesapeake, VA
- Vehicle(s)
- 2025 Bronco Raptor
- Your Bronco Model
- Raptor
- Thread starter
- #50
I used Kicker cs for mine. Had to cut 2 off the mounting tabs off for them to fit. I also poly fill inside the pod first. Zero rattle from mine. I have talked to someone else though that their 2026 the pods aren't the same.
Sponsored
Easy fix: sound deaden inside of pods, and tesa or thin foam tape on any pod / body contact points, and speaker / pod interface.
Here is what i upgraded with along with a couple pictures sorry didn’t photo the other speaker replacements:
Front Dash: Kicker KSC40
Center Speaker: Kicker 46CSC44
Kick Panel: Kicker KSS670
Rear Pods: Kicker 51KSC6504
SSV 6.5” Bronco Raptor Rear Speaker POD
Sub: Stinger 12” Tailgate Enclosure
(Audio Control SPC-12S2 (12” 2ohm))
Amps: Kicker Key200.4 & Key500
Front Dash: Kicker KSC40
Center Speaker: Kicker 46CSC44
Kick Panel: Kicker KSS670
Rear Pods: Kicker 51KSC6504
SSV 6.5” Bronco Raptor Rear Speaker POD
Sub: Stinger 12” Tailgate Enclosure
(Audio Control SPC-12S2 (12” 2ohm))
Amps: Kicker Key200.4 & Key500
OP
OP
- First Name
- Hoyt
- Joined
- Dec 29, 2025
- Threads
- 2
- Messages
- 43
- Reaction score
- 95
- Location
- Chesapeake, VA
- Vehicle(s)
- 2025 Bronco Raptor
- Your Bronco Model
- Raptor
- Thread starter
- #53
Here is what i upgraded with along with a couple pictures sorry didn’t photo the other speaker replacements:
Front Dash: Kicker KSC40
Center Speaker: Kicker 46CSC44
Kick Panel: Kicker KSS670
Rear Pods: Kicker 51KSC6504
SSV 6.5” Bronco Raptor Rear Speaker POD
Sub: Stinger 12” Tailgate Enclosure
(Audio Control SPC-12S2 (12” 2ohm))
Amps: Kicker Key200.4 & Key500
That was a non B&O system correct? I ask because on b&o system the kick panel kickers sound like garbage
Nice fab work and install. Consider some amp mount spacers and vent holes in the mount all that open air in qtr panel is a rare blessing for heat management, as is the open old sub grill can't imagine a better convection cooling set up.Here is what i upgraded with along with a couple pictures sorry didn’t photo the other speaker replacements:
Front Dash: Kicker KSC40
Center Speaker: Kicker 46CSC44
Kick Panel: Kicker KSS670
Rear Pods: Kicker 51KSC6504
SSV 6.5” Bronco Raptor Rear Speaker POD
Sub: Stinger 12” Tailgate Enclosure
(Audio Control SPC-12S2 (12” 2ohm))
Amps: Kicker Key200.4 & Key500
It was B&O system. i just used the 6.75 driver of Kicker component system. I put sound deadening and polyfill in each space before installing speakers.
Sponsored
Nice, but how are you running 7 speakers off a 4 channel amp? Or did you use some type of component crossover setup to split low, mid and high freq output up front?Here is what i upgraded with along with a couple pictures sorry didn’t photo the other speaker replacements:
Front Dash: Kicker KSC40
Center Speaker: Kicker 46CSC44
Kick Panel: Kicker KSS670
Rear Pods: Kicker 51KSC6504
SSV 6.5” Bronco Raptor Rear Speaker POD
Sub: Stinger 12” Tailgate Enclosure
(Audio Control SPC-12S2 (12” 2ohm))
Amps: Kicker Key200.4 & Key500
Here is what was used to interface with the factory head unit.
https://www.crutchfield.com/S-jGDs0...38nGJLFjCP3f1NVkC8bcQDPon4q2QnvhoCbf0QAvD_BwE
Sorry , I guess I am still not seeing how you are running all the wiring? Forgive me, I am just trying to follow how some are bypassing the factory B&O amp in their rides. I see that the PAC takes the factory connections to give you 3 sets of Pre-AMP outputs (2 front, 2 rear and sub). So I take it as you are unplugging the B&O amp, which powers 8 speakers (2 kick, 3 dash, 2 rear and a sub) and plugging that harness into the PAC box. How are you running all your speakers? Thanks for helping me out, I really want to upgrade my system and this seems like a good solution.
I didn’t do the wiring part, took to a trusted installer I’ve used on other vehicles. The b/o amp was completely removed. I will reach out to them as ask them your question.
I’m guessing that when it says Front it refers to the L/R Dash and L/R Kick Panels as Fronts, Rears are the PODS, the center and then the sub. i don’t think the center is amplified but will clarify that as well. All I know is that it sounds good, hits when I want it too.
Thanks man, I appreciate you.
Sponsored
