What did you do TO / WITH your Bronco today? 👨🏻‍🔧🧰🚿🛠

[PrepVet]

Got it washed. Looks to be some nasty weather over the next several days.

Sponsored

 

[‘21OBX]

Little project completed today. I’ve been wanting these for a while now. Start by popping the hood. There are push pins that you have to gently lift the middle up then the entire things can pull out.

once those are all removed gently pull up and wiggle the close out trim out from under the air intake.

then you have 4 10 mm head bolts to remove and unplug the camera and camera washer hose if equipped

then gently pull the grill straight out I start on the sides then pull from the middle.

then gently lift the grill out and away.
find a soft place to lay the grill I used a floor mats and a plastic tub since we don’t use the floor mats for anything else.

gently GENTLY!! Drill the white plastic only!!! To remove the stock letters. Once they are all removed install the new ones. They slide right into the existing holes. The directions said to use washers. My kit didn’t included them but they are needed. The provided screws are a touch too long.

the connectors provided are not water tight so I sealed them with silicone to prevent corrosion. Then test before you install!! Once you verify they work(and in my case get surprised that the letters flashed and stuff). Install is the reverse of removal. I temporarily wires them as the website says. But am. It fond of the setup so I will rewire them later. The fuse box cover does not fit securely is what I don’t like. Then you just enjoy your new addition!!

 

[KTP 30]

I really need this mirror decal!
Also, is that an OEM blind spot mirror? Part of the towing package? I’m about ti stick on some crappy Amazon blind spot mirror, don’t recall seeing this on the options list…

It the mirrors on the Base.

 

[Browp24]

Are these oracle letters? If not do you have a lunk to them? Sorry if you answered this in a earlier post

Little project completed today. I’ve been wanting these for a while now. Start by popping the hood. There are push pins that you have to gently lift the middle up then the entire things can pull out.

once those are all removed gently pull up and wiggle the close out trim out from under the air intake.

then you have 4 10 mm head bolts to remove and unplug the camera and camera washer hose if equipped

then gently pull the grill straight out I start on the sides then pull from the middle.

then gently lift the grill out and away.
find a soft place to lay the grill I used a floor mats and a plastic tub since we don’t use the floor mats for anything else.

gently GENTLY!! Drill the white plastic only!!! To remove the stock letters. Once they are all removed install the new ones. They slide right into the existing holes. The directions said to use washers. My kit didn’t included them but they are needed. The provided screws are a touch too long.

the connectors provided are not water tight so I sealed them with silicone to prevent corrosion. Then test before you install!! Once you verify they work(and in my case get surprised that the letters flashed and stuff). Install is the reverse of removal. I temporarily wires them as the website says. But am. It fond of the setup so I will rewire them later. The fuse box cover does not fit securely is what I don’t like. Then you just enjoy your new addition!!

 

[‘21OBX]

Are these oracle letters? If not do you have a lunk to them? Sorry if you answered this in a earlier post

Not sure how to link. Mine are white but they are this brand on Amazon $99.99

 

[Jeffem]

Installed Cargo Light
Triggercontroller.com
Dual LED Strip.
On / Off switch
$30
5 minute install
Power from 12 volt plug

 

[zjc26138]

Put some Christmas lights on the back.
Might run lights along the edge of the top and down to trail sights as well. Lol.

 

[Micha]

Super dumb and no one will ever notice it but me

What kind of mirror is it? Can you take a full view pic ?

 

[KABQ]

What kind of mirror is it? Can you take a full view pic ?

It's just the factory Base mirror. My post referred to the silly sticker I put on the it, but I can take a pic of the whole mirror if you want.

 

[604Bronco]

Now that's the face of a happy Bronco owner...

 

[Micha]

It's just the factory Base mirror. My post referred to the silly sticker I put on the it, but I can take a pic of the whole mirror if you want.

your mirror looks divided to two mirrors(is it?)

 

[JonDW29]

your mirror looks divided to two mirrors(is it?)

Believe those are the mirrors for Broncos without BLIS.

 

[PrepVet]

Believe those are the mirrors for Broncos without BLIS.

Correct.

 

[MannyG20]

Little project completed today. I’ve been wanting these for a while now. Start by popping the hood. There are push pins that you have to gently lift the middle up then the entire things can pull out.

once those are all removed gently pull up and wiggle the close out trim out from under the air intake.

then you have 4 10 mm head bolts to remove and unplug the camera and camera washer hose if equipped

then gently pull the grill straight out I start on the sides then pull from the middle.

then gently lift the grill out and away.
find a soft place to lay the grill I used a floor mats and a plastic tub since we don’t use the floor mats for anything else.

gently GENTLY!! Drill the white plastic only!!! To remove the stock letters. Once they are all removed install the new ones. They slide right into the existing holes. The directions said to use washers. My kit didn’t included them but they are needed. The provided screws are a touch too long.

the connectors provided are not water tight so I sealed them with silicone to prevent corrosion. Then test before you install!! Once you verify they work(and in my case get surprised that the letters flashed and stuff). Install is the reverse of removal. I temporarily wires them as the website says. But am. It fond of the setup so I will rewire them later. The fuse box cover does not fit securely is what I don’t like. Then you just enjoy your new addition!!

I think we found our extrovert.
Seriously, I love the random opening before all the lights come on.

 

[jar1229]

Last night I installed the Oracle Lighting Triple LED Fog Light Kit using the factory Aux Switches. Relatively straight forward process, and I absolutely LOVE how these lights look! One of my top 3 overall mods so far! Hope this video helps people out who want to hook them up to their Aux Switches:

Question if you do not mind. I just ordered the Oracle lights and on their site it states should only use 1 fog light on main roads and obviously all 3 when off roading. My question is were you able to use two different Aux Switches say AUX1 and AUX2 to power 1 light and 3 lights?

Appreciate the help.

Sponsored