Search results

A little late, but this was my method to avoid this. https://www.bronco6g.com/forum/threads/read-this-before-installing-a-tailgate-reinforcement.68158/page-4#post-2196796

I went with the LED grab handles in the front and couldn't be happier. https://a.co/d/0fZpp0IQ

Don't know that they could be any worse.

I'm pretty sure it is the Broaddict one, I can verify when I get home. My seats are reclined all the way, but I did have to make a small mod to make that happen. I just picked up a couple spacers and a couple longer bolts and installed them in the lower hole, causing the panel to sit at an...

According to my dealership, it was only covered by the remaining 3/36, and my 3/36 ended 1 month after replacement. The top didn't start showing cracks until about 4.5 months after replacement. Top was replaced end of February and I noticed cracks beginning of July.

My 22 is garage kept, had 1st top replaced 1 month before my 36 month warranty ended at 26,000ish miles, 6 months later replacement top started cracking at 28,000ish miles, ford told me to pound sand, 3yr/36000 had expired and the extended warranty would not cover it because it is "considered...

Link to my original ad. https://www.bronco6g.com/forum/threads/modular-bumper-w-sensor-holes.119858/

I have no need for a trade as I went with the DV8 tube bumper, but i have everything I took off of my 22 Wildtrak that I will make you a deal on. The bumper does have almost 30K miles on it, so it does have some rock chips and and stuff from normal driving. It would be everything needed, and the...

Just trying to clarify, you have a capable bumper and want a modular bumper or the other way around? Also with or without sensor holes?

If you don't want to mess with forscan, there is always the superchips flashcal, it will allow you to correct your speedometer and make some other changes as well, like turning off the auto start/stop.

Do it now. I waited until my warranty was almost up to have mine changed out, then the replacement top started cracking less than 6 months later and ford will not warranty it because it is no longer under the 3/36. Warranty the top as many times as possible, it might improve your chances at...

Modular bumper: Sold Also have a set of SPV triple pod light mounts for $75 and SPV modular bumper light mounts for $75. Would prefer to give first option of these to purchaser of bumper. If not sold in a week or so, I will sell separately and would be willing to ship these on buyer's dime...

Good to know it's upgraded and compatible with thicker floor mats. I can see where that would be important.

Did you remove the shutters? They occupy the same location the light bar will be in.

What you are speaking of are cradles, Daystar used to make them, not sure if they still do, but I had a set on my tundra. They are essentially a plastic bowl that the bottom of the bag just sits in and if you droop beyond the limits of the bag, then the bag just comes out of the cradle. When you...

4 door wildtrak, best I can tell from measuring another 4 door wildtrak, I gained approx .5" lift in the front and none in the rear. So, approx 1.7" from base suspension height. Really sucks that you have to remove the coilovers from the vehicle to adjust the height.

Well, my 4 month old replacement rear clamshell is starting to crack.

A nice day off deserves new pics.

When i built mine, I found the easiest way to get the curve, was to place some painters tape across the inside and top edge of the tailgate, placed the board in place on top of the tailgate, squeezed myself into the cargo area, closed the tailgate, and traced the curve of the tailgate.

Do you do 5 tire rotations? That looks like the rubber bumper that supports the tire on the tailgate just left a wear mark/indentation. You can have it checked, but i would say that it's fine. There's no broken belts, so at worst it's just ugly.