Search results

You're not alone! I have the same issue (steering wheel looks to be so slightly to the right ) Annoying, but it does track straight enough.

I tried my best with the overview that I wrote up. I don't write technical manuals for a living so.... It was the best I could do. On a side note, my first car was the 69' Spitfire. And I just sold my 85' Rover (thus Rover Dude) to make room in the garage for the bronco. If you PM/DM me with a...

Out of curiosity, what lines were different? or what values did you have? (you can PM me your vin so i can pull the asbuild data too if wanted.)

Pictures As requested! This is the Exact same setup as the factory hitch. The factory hitch fit snug under the Spare *Can't see it close up*: From Side: Down Low: With Gate Open (Spare not in Way) Closes up of just the Hitch: Other then a green marker on the bolt to show...

That harness is included buying Ford version "VM2DZ-2C006-A" Still probably not cost effective. But I used my passpoints to buy it.

Like I mentioned, There are (2) fused hots: Fuse91 (40A) powers the unit - this is what creates the Left Signal, Right Signal, and Parking Lights Fuse107 (30A) feed goes to an internal relay and out on the orange wire (battery charger connection). Those are the 2 blue wires in the 1 Connector...

That is the (Ford Trailer Brake Controller made by Redarc) part# VM2DZ-2C006-A That is where I installed the control knob. It comes with a template and instructions to install it in the center console. It doesn't look right there, in my opinion. Like others have done, I drove the hole and...

It does not come with a brake controller. But the connections for it plugged and play. There's a power connection in every bronco sitting capped off above the driver's right foot. The switch /nob just has to be mounded somewhere. Instructions that come with the kit have the controller mounted...

I am not saying that it's going to be cheaper. I believed I use the same components that would come on the tow package. I know the wire I use was not the same, GLX has a thicker Insulation/ Higher temperature rating. It wasn't necessarily hard.

I wanted to have the factory hitch for my Bronco, but that was not an option. I have gotten all the parts separately and have a complete OEM solution for adding the factory tow package to my 4 door First Edition. I have everything installed and have been able to configure it in Forscan to have...

Question: did they "WOW You?".

Todd here from the Dena, Area 51 FE.

I have not made much progress. I don't have any documentation on the pinout for the IMPB. I don't know if this module is used in other vehicles (not that I found) I have not tried to see if I could input this into the sync 4 module behind the screen. (For me , It's a lot of dash to take apart...

The backup camera without the 360 camera view is an analog input I believe. The 360 cameras which is on the high package and up is an digital input. The digital inputs goes to the ipmb module. I do not believe there's a impb module unless you have the 360 cameras (that's based on as build...

Bob Bell in Glen Burnie. FE at MSRP. No games, strait forward experience ( Better then I expected). First and only purchase from them... BUT I would go back to them based on my experience purchasing the Bronco.

So I have been having conversations with XirallicBolts, and in theory made some progress. I should be able to test something within a week. I have been able with forscan to get the icon for AUX AND Trailer to show up as a source. But I never had an input there. Currently I believe you can only...

Soo, I am wondering if anyone knows if it is possible to add an addition camera into the Sync 4 system. I have a FE, so it already has the 4 cameras, but is it possible to add (1) one more, (somehow?), then active that extra camera with Forscan? My goal is to have this extra “Bonus Camera”...