did you use the suggested LED strip?Credit to the OP on maker world but this was fun and cool to make.
link here if anyone else is interested was really easy.
https://makerworld.com/models/143578?appSharePlatform=copy
Sponsored
Sponsored
Show me your 3D printed accessories. 3D Prints for Bronco Enthusiasts.
- Thread starter I3lackRose
- Start date
- Watchers 142
I used this one so I could have a remote and change colors… I had to trim just a tiny bit where it entered the frame but otherwise pretty good
Lamomo Led Strip Lights, 16.4Ft... https://www.amazon.com/dp/B0D5B69GF4?ref=ppx_pop_mob_ap_share
Make sure you double-check that the strip you get is cuttable like the one @ejedmo5 linked.
There are a lot of options and some can be integrated into Home Assistant, etc. so you can control it via smart home stuff.
- First Name
- Julian
- Joined
- Mar 11, 2021
- Threads
- 13
- Messages
- 252
- Reaction score
- 387
- Location
- NewHampshire
- Vehicle(s)
- Atlas/65Mustang
- Your Bronco Model
- Heritage
Just throwing this in here. Quick remove brackets for the BHBTFD license plate holder. Wanted to be able to take off the plate quick and easy without tools. (Car wash ripped my bracket partly off)
If anyone is interested, I will look into getting the file up for printing. Green was a prototype in PLA. Knob is shrunken down in the final print.
If anyone is interested, I will look into getting the file up for printing. Green was a prototype in PLA. Knob is shrunken down in the final print.
- Joined
- Dec 15, 2020
- Threads
- 103
- Messages
- 4,852
- Reaction score
- 9,144
- Location
- Portland, Oregon
- Vehicle(s)
- Mustang
- Your Bronco Model
- Badlands
Of course I got the non-cuttable version. I will just have to design my own frame to fit the light strip.
Last edited:
Sponsored
Of course I got the non-cuttable version. I will just have to design my own frame to fit the light strip.
[/QUOTE]
Or add some extra design on the end to use the slack.
(I've ordered the wrong kind at least 3 times so far)
- Joined
- Dec 15, 2020
- Threads
- 103
- Messages
- 4,852
- Reaction score
- 9,144
- Location
- Portland, Oregon
- Vehicle(s)
- Mustang
- Your Bronco Model
- Badlands
Or add some extra design on the end to use the slack.
(I've ordered the wrong kind at least 3 times so far)
[/QUOTE]
I want to make it bigger. Because.... 'Merica!
Do you have the print file available for the tpu insert?Im still iterating on this. Aside from the TPU insert I’ve added a second set of screws to further enhancement the rigidity and a corresponding gusset for them. Same with ribs on the inside of the pocket. Thankfully @ejedmo5 did a brilliant job with the design so tweaking is the fun part.
- Joined
- Dec 15, 2020
- Threads
- 103
- Messages
- 4,852
- Reaction score
- 9,144
- Location
- Portland, Oregon
- Vehicle(s)
- Mustang
- Your Bronco Model
- Badlands
Not yet. I want to test it some more. The first iteration is too snug and pretty useless since it comes out with your drink bottle.
Sponsored
@swooshdave is it already just TPU on the bottom or did you have it go up the sides? I can see just the bottom with a TPU insert that's ribbed to prevent suction when you pull your cup out. That and some 3M 90 adhesive spray might do it.
- Joined
- Dec 15, 2020
- Threads
- 103
- Messages
- 4,852
- Reaction score
- 9,144
- Location
- Portland, Oregon
- Vehicle(s)
- Mustang
- Your Bronco Model
- Badlands
I went up the sides.
- Joined
- Dec 15, 2020
- Threads
- 103
- Messages
- 4,852
- Reaction score
- 9,144
- Location
- Portland, Oregon
- Vehicle(s)
- Mustang
- Your Bronco Model
- Badlands
I don't give up that easily.
They came out perfect. I did leave them in the oven to anneal them. Hopefully they survive the Texas heat. Also ordered some eruption green paint, I’ll update whenever it comes in.
I did have little gaps that I need to put some weather stripping around. Probably add some foam behind the cupholder to make it fit tighter and prevent rattling.
I did have little gaps that I need to put some weather stripping around. Probably add some foam behind the cupholder to make it fit tighter and prevent rattling.
I did a cup holder for something else that had captive tpu inserts, could look at thatI don't give up that easily.
looks great shocked at how many people have printed them, I do agree with adding some thing to keep them from rattling. Still not bad for me using a tape measure and cardboard for basically all of itThey came out perfect. I did leave them in the oven to anneal them. Hopefully they survive the Texas heat. Also ordered some eruption green paint, I’ll update whenever it comes in.
I did have little gaps that I need to put some weather stripping around. Probably add some foam behind the cupholder to make it fit tighter and prevent rattling.
Sponsored
