Enabling Intelligent Adaptive Cruise Control and Lane Centering

[BoringB6]

That was my factory coding. I had changed the “3” to “F” but have sense changed it back. My Bronco has the 2.7.

Sponsored

 

[dannyss]

Following,
I've got the same 760-03-01 coding: 3480-004C-DF4A
Also tried changing the 3 to an F and got a "Check digit" incorrect when writing.

 

[RoverDude]

Following,
I've got the same 760-03-01 coding: 3480-004C-DF4A
Also tried changing the 3 to an F and got a "Check digit" incorrect when writing.

the last 2 digits are the checksum:
760-03-01: 3480-004C-DF4A
changing the 3-> F would mean it should be:
760-03-01: F480-004C-DF0A

 

[dannyss]

Thanks,
While taking note of the new value with new checksum I noticed that my value is 3480-004C-1F8A.
Is the algorithm known to calculate the new checksum?
So, the checksum you gave me is incorrect

 

[helifino16]

The wife has the Collision Avoidance braking system on her Mazda. I've had it activate a couple times when someone abruptly decides to brake too much for a turn in front of me. It's a bit startling, but realize it's a relief and responds way faster than I could. It might be something I'd like on the Bronco vs the beeping "BRAKE!" signal. It probably would remind me not to tailgate (I know, a bad habit I picked up after years of driving in NY).

 

[RoverDude]

Thanks,
While taking note of the new value with new checksum I noticed that my value is 3480-004C-1F8A.
Is the algorithm known to calculate the new checksum?
So, the checksum you gave me is incorrect

What I gave you was not incorrect for your listed value

Thanks,
While taking note of the new value with new checksum I noticed that my value is 3480-004C-1F8A.
Is the algorithm known to calculate the new checksum?
So, the checksum you gave me is incorrect

is what you said originally
760-03-01: 3480-004C-DF4A

What you said currently
So, the checksum you gave me is incorrect
NO, you now have different digits
3480-004C-1F8A.
is different
3480-004C-DF4A

 

[Giovani13]

I'm sorry if I'm missing something. Was this ever resolved for the 2025? I was just out in the driveway ready to code this for my 2025 Badland LUX and I wasn't sure what value to put in the ABS 760-03-01 location.

 

[ptgptg]

I'm sorry if I'm missing something. Was this ever resolved for the 2025? I was just out in the driveway ready to code this for my 2025 Badland LUX and I wasn't sure what value to put in the ABS 760-03-01 location.

I believe the below was added by Strizzo as the most recent directions at the top of the thread and all you do is (1) BCM change to adaptive CC, stop and go (2) change the first entry to an "F" in the 760-03-01 and (3) do a PCM relearn.

I only added the stop & go with just the body control modue and ABS changes at this point, once the intelligent with speed sign reading is sorted, i'll make those changes as well. The order I did them in was
1. BCM change cruise control to adaptive Cruise Control, Stop & Go
2. ABS 760-03-01 to F*** ****, then
3. PCM relearn. - I'm not sure this was absolutely required as I did not have any active codes after the ABS change.

Since the as built entries in the ABS position are in question, I took a screenshot of the asbuilt for the ABS position, originally it was B:

 

[Giovani13]

I only added the stop & go with just the body control modue and ABS changes at this point, once the intelligent with speed sign reading is sorted, i'll make those changes as well. The order I did them in was
1. BCM change cruise control to adaptive Cruise Control, Stop & Go
2. ABS 760-03-01 to F*** ****, then
3. PCM relearn. - I'm not sure this was absolutely required as I did not have any active codes after the ABS change.

Since the as built entries in the ABS position are in question, I took a screenshot of the asbuilt for the ABS position, originally it was B:

Stop & Go is fine by me. What I'm seeing is our as built are different, yours is eight characters, mine is twelve.

Your as built: B818 90CB
My as built: 3480 004C DF4A

I'll try changing to F*** **** **0* as RoverDude suggested. Though I don't think there has been any confirmation that works.

 

[ptgptg]

Sorry, I didn't catch that until you pointed it out. Maybe my wife is correct and I am useless!.

 

[RoverDude]

Stop & Go is fine by me. What I'm seeing is our as built are different, yours is eight characters, mine is twelve.

Your as built: B818 90CB
My as built: 3480 004C DF4A

I'll try changing to F*** **** **0* as RoverDude suggested. Though I don't think there has been any confirmation that works.

My as built: 3480 004C DF4A

I have no idea on the 2025,
Question: do you have a manual?

for prior to 2025
Your asbuilt start with 3

3 means you do not have Adaptive Cruise Control or Collision Mitigation by Braking
B means you have Adaptive Cruise Control but do not have Collision Mitigation by Braking
F means you have Adaptive Cruise Control AND have Collision Mitigation by Braking

 

[Giovani13]

My as built: 3480 004C DF4A

I have no idea on the 2025,
Question: do you have a manual?

for prior to 2025
Your asbuilt start with 3

3 means you do not have Adaptive Cruise Control or Collision Mitigation by Braking
B means you have Adaptive Cruise Control but do not have Collision Mitigation by Braking
F means you have Adaptive Cruise Control AND have Collision Mitigation by Braking

It's automatic. A badlands, sasquatch, lux package. I do have adaptive cruise, and collision.

 

[Giovani13]

I can confirm this does not work.

1. BCM change cruise control to adaptive Cruise Control, Stop & Go
2. ABS 760-03-01 to F*** **** **0*, then
3. PCM relearn.

 

[whtwtrchic]

That was my factory coding. I had changed the “3” to “F” but have sense changed it back. My Bronco has the 2.7.

Were you ever able to get the IACC stop and go to work on your 2025 2.7L? I was hoping to do the same.

 

[BoringB6]

No unfortunately… Like Giovani13 mine says cruise not available. Hoping someone smarter than me figures it out.

Sponsored