HERITAGE EDITION Bronco Club

[Lowcountry Bronco]

Here’s something different I seen… not sure how I feel about it yet…

Hmm ... no offense but don't like, looks like one of the badges you'd see on a dealer prep'd lot special for $7995 extra.

Sponsored

 

[Kenny86]

I wanted the vintage look for the ditch lights and went with the 4” KC HiLites.

They look pretty good and blend well! Thanks for sharing.

 

[GMC]

Is the Bronco fender decal separate from the stripe?

 

[JawnyBronco]

Is the Bronco fender decal separate from the stripe?

Nope, part of it…

 

[Lowcountry Bronco]

Is the Bronco fender decal separate from the stripe?

Nope, would have been allot easier and cheaper on everyone if it was!

 

[Jbatey84]

Thanks all, seeing as ours are gone can I get someone to roughly measure the normal heritage Bronco script?

Also a limited edition heritage script measurement if possible?

Thanks so much.

 

[Lewisj41]

Saw my first two door heritage, Race Red in Middletown MD today. It was too quick to grab a picture. Not sure if you're in here?

 

[Brave Man]

Thanks all, seeing as ours are gone can I get someone to roughly measure the normal heritage Bronco script?

Also a limited edition heritage script measurement if possible?

Thanks so much.

For the standard Heritage:
the length of the script is 7-3/4“
the height is 1 -1/2 “ for the capital B , 5/8” for the non capitalized letters

 

[GMC]

Nope, part of it…

Nope, would have been allot easier and cheaper on everyone if it was!

Thanks. I take it everything is just one big decal with clear vinyl in the center. I much prefer the badges to the decals, but I wonder if the UG stripes are really as easy to install as their video shows. OCD and crooked stripes are a bad combo.

 

[Calypso]

OK class, here we have:

TOP: Bronco Heritage Limited, ~9" long x 1-7/8" at the capital B, 3/4" at the 'ronco'.

MIDDLE: Bronco Heritage, as per Brave Man:

For the standard Heritage:
the length of the script is 7-3/4“
the height is 1 -1/2 “ for the capital B , 5/8” for the non capitalized letters

BOTTOM: Archetype Racing, 10-5/8" long, 2-7/8" high from top of placard to the bottom of the capital B, 7/8" high for the 'ronco'.

BONUS from back when the Bronco hype was really tall: at bottom, Bronco Depot, essentially the same size script as Archetype. 2-1/8" high on the capital B.

I've gotta get rid of some of this stuff .

 

[Lowcountry Bronco]

Thanks. I take it everything is just one big decal with clear vinyl in the center. I much prefer the badges to the decals, but I wonder if the UG stripes are really as easy to install as their video shows. OCD and crooked stripes are a bad combo.

My story has been posted a few times but I paid a shop to remove the front stripes and replace with the Limited ones I bought, think they were going to charge me $300. The OEM stripes didn't work, they were too light/thin for whatever reason and they looked more gray and didn't match the ones that were left on. At that point the shop had already removed both front sides so I was at quandary, I could have went with UG stripes but the shop wasn't excited about putting someone elses vinyl on and said they could make me a set, so they did. Out the door was around $800 if I remember correctly for their work to replace all the factory stripes, bad part is that I spent close to $300 for the Limited fronts.

So, if you're still with me, what I'd do is find a good shop that doesn't mind putting on the UG stripes and just remove the factory stripes yourself before dropping it off. Depending on where you are I don't think it would be a crazy price and they'd at least guarantee their labor and ensure they're on straight. From there you can put on whatever script you want at whatever price you feel like paying.

Anyrate, good luck and post back whatever you get done!

 

[Lowcountry Bronco]

OK class, here we have:

TOP: Bronco Heritage Limited, ~9" long x 1-7/8" at the capital B, 3/4" at the 'ronco'.

MIDDLE: Bronco Heritage, as per Brave Man:

BOTTOM: Archetype Racing, 10-5/8" long, 2-7/8" high from top of placard to the bottom of the capital B, 7/8" high for the 'ronco'.

BONUS from back when the Bronco hype was really tall: at bottom, Bronco Depot, essentially the same size script as Archetype. 2-1/8" high on the capital B.

I've gotta get rid of some of this stuff .

I think you did the same thing I did, just but them all and figure out which you like best!

Only ones you missed were the original, Stickerfab sells those and removes the pins, they list them as 10.5" x 2.25"

https://www.stickerfab.com/products/ford-licensed-bronco-cursive-metal-emblem-kit-2021-bronco

i think those match up to the badgeslide ones I have down in the garage.

 

[5GENIDN]

So, if you're still with me, what I'd do is find a good shop that doesn't mind putting on the UG stripes and just remove the factory stripes yourself before dropping it off. Depending on where you are I don't think it would be a crazy price and they'd at least guarantee their labor and ensure they're on straight. From there you can put on whatever script you want at whatever price you feel like paying.

Anyrate, good luck and post back whatever you get done!

Sorry (you may run into some of this but) I will not install someone else's vinyl... the reason is that although my guys are really good, mistakes can and do happen occasionally. If I did not create (cut) the vinyl then I can not reproduce it to make the job right. I have seen that happen from time to time. Not often, but when it does, it is a mess....

 

[EvilJim1971]

Only ones you missed were the original, Stickerfab sells those and removes the pins, they list them as 10.5" x 2.25"

https://www.stickerfab.com/products/ford-licensed-bronco-cursive-metal-emblem-kit-2021-bronco

i think those match up to the badgeslide ones I have down in the garage.

A warning about those, do not use the template they come with, it doesn't work for our fenders.
I spent a bit of time with a couple pairs of padded pliers trying to get them to conform to the fender shape and decided that close would have to work so I didn't break them.
To do it over I would go with the ones for the Limited... or at least non metal ones.

 

[Calypso]

I think you did the same thing I did, just but them all and figure out which you like best!

I'm going with the Heritage Limited badge, its luster matches that of the tailgate Bronco best.

Now that spring is here, just waiting for a break in the pollen drop to tackle the job. Ford could've named 'Cactus Gray' as 'Pollen Green', it really matches well.

I also have the Heritage Limited stripes to apply, we'll see if they match better over the gray paint than they did on @Lowcountry Bronco 's Azure Gray.

Sponsored