What did you do TO / WITH your Bronco today? 👨🏻‍🔧🧰🚿🛠

[Muddog899]

I don't get the little bronco but I have a base

Sponsored

 

[TEAMSLO]

EDITED: Have since removed this and the LP6's had an extreme bobble head effect making it almost unusable. Have gone to Vivid Racing's mount: LINK

Been a busy almost couple of months, just put on the bar and BD LP6 yesterday. Hoping to get the HW kit in today and get the RCI sliders mounted as well. Ordered the BRONCO grill lettering in gloss black to mask it a bit.

 

[cynicalrider]

I don't get the little bronco but I have a base

You don't have active cruise because that's on the lux package.

 

[Ironiguana]

Added these from StickerFab:
https://www.stickerfab.com/products...series-vinyl-universal?variant=40992311279727

I like how it gives the letters a more 3D look:

 

[zedster]

My passenger window door regulator was replaced under warranty for creaking when opening and closing the door. I could somewhat hear it when driving too.

 

[mpeugeot]

How do you get this screen

Night mode...

 

[cgv]

Installed my Turn Offroad sliders! Wife and kids love the step to help get in and out. Love the look and quality, though I did have a slight issue with fitment on the center brackets that I'll detail in another thread.

Also figured out what the terrible squeak was that had been getting consistently worse. It was the rear bolts and crossmember insert on my ARB transmission skid. White lithium spray did the trick!

 

[PullMeOverRed22]

After sanding, priming, painting, cutting a bucking bronco stencil, then painting some more - here is my JCROffroad engine cover installed! Thank you to @KRAKEN for the design inspiration and @JcrOffroad for a quality product.

That is one clean engine compartment!

 

[Area51BS]

Hauled new coffee table. Not a huge issue. But Ford could have designed fold flat seats.

 

[retiredarmymp]

After sanding, priming, painting, cutting a bucking bronco stencil, then painting some more - here is my JCROffroad engine cover installed! Thank you to @KRAKEN for the design inspiration and @JcrOffroad for a quality product.

Great minds think alike!

 

[Ninjak]

Hauled new coffee table. Not a huge issue. But Ford could have designed fold flat seats.

I know what you are saying. I had to replace a toilet, luckily it went in width-wise. This though is why I want the pull-out tray. It will level the back out. I just do not want tp spend the money. Hoping for a sale or wait till I get more points.

 

[Area51BS]

I know what you are saying. I had to replace a toilet, luckily it went in width-wise. This though is why I want the pull-out tray. It will level the back out. I just do not want tp spend the money. Hoping for a sale or wait till I get more points.

I wouldn’t want to loose any cargo height capacity with a tray. Especially since umbrella top doesn’t open as far as hard top glass. A tray would be convenient depending how you use the Bronco. Diabolical makes a nice one.

 

[mikejames]

Installed IAG I-Line Mini Mud Flaps (https://iagoffroad.com/iag-i-line-2pc-rock-rail-side-mini-mud-flap-2021-ford-bronco/) in the end of the rock rails.

Pretty straightforward. The hardest part of the install was getting the top screw to go in - there's no room for a screwdriver to go in straight, and I didn't want to drive it at a weird angle. Maybe a low profile driver would make this easier, but it's quite close to the body.

What I ended up doing was:

1. dry fit the flaps and mark hole locations on the plastic by pressing screw in
2. take flaps out and drill pilot holes at marked locations
3. Pre-screw the hard to reach one, to make final install easier
4. Use a phillips bit (sans screwdriver) and a set of Leatherman pliers to slowly turn the screw until it was all the way in.

A slightly tedious process, but results were excellent.

 

[dgorsett]

Installed my towed vehicle battery charger trying to avoid flat tow issues.

 

[18KingRanch]

Added the Mountian2Metal rear cargo tray and the DV8 Molle panels.

Sponsored