Mabett launches Tailgate Table with Cutting Board!

[Mabett]

Buy "Tailgate Table with Cutting Board" directly for $239.99 via this link: https://www.amazon.com/promocode/A18NVLYTTHC7AR

Attention! All the pictures don't have the mabett logo, but it actually has the mabett logo!!!

Product Description

• Adds a Convenient Table to Your Bronco’s Tailgate
• With Mabett Logo on Metal Surface
• Made of iron, Black Powder-Coat finish.
• Sports a Sleek, Foldable Design
• With 2 Cup Holders and Cutting Board
• Fully Bolt-on, no drill installation.
• Quiet, no rattle cargo solution.
• Supports Up to 75 lbs.

Sponsored

 

[SwampCactus]

Keep up the good work guys. Love how you keep coming out with stuff for the Bronco.

 

[nwGTS]

Purchased! Yes! So glad you brought this to market and at a great price. The logo is nothing a few decals cant take care of.

 

[Kfonte]

The tailgate table we never thought we needed, but now we can’t live without

 

[R1Bronco]

Just ordered mine....Nice looking and love the cutting board...
No drilling, uses the accessory ready panel like it was meant for....

 

[nwGTS]

I installed mine today @Mabett

the clasp hardware that holds the table closed is trash and pops loose when closing the gate.
Also many of the small attachment screws holding the hinges, clasps and retention arms were not fully fastened. So it rattled terribly until i discovered this and had to partially disassemble it to fasten all the small screws.

at a minimum this needs new clasping hardware to be functional.
I have it closed with gorilla tape until I can figure something out.

 

[R1Bronco]

I installed mine today too @Mabett
The locking clasp needs to be better quality....Mine was bent and falling apart, had to use pliers on them....
And the tiny screws holding one of the pieces that blocks the wind fell out and I found them in the packaging...I put locktight on them.
I had to go around and tighten a few other Allen screws and nuts too....
For as much as this cost I shouldn't have to do this....
The table looks good and feels solid once tightened all down,except for the fasteners, you guys need to replace them....

 

[doyouglas]

Are there any quality control on these table?

 

[nwGTS]

I installed mine today too @Mabett
The locking clasp needs to be better quality....Mine was bent and falling apart, had to use pliers on them....
And the tiny screws holding one of the pieces that blocks the wind fell out and I found them in the packaging...I put locktight on them.
I had to go around and tighten a few other Allen screws and nuts too....
For as much as this cost I shouldn't have to do this....
The table looks good and feels solid once tightened all down,except for the fasteners, you guys need to replace them....

I had the exact same problem with the toggle latches falling apart too. They need to use better toggle latches and be sure all the fasteners are torqued.

 

[Mabett]

I installed mine today @Mabett

the clasp hardware that holds the table closed is trash and pops loose when closing the gate.
Also many of the small attachment screws holding the hinges, clasps and retention arms were not fully fastened. So it rattled terribly until i discovered this and had to partially disassemble it to fasten all the small screws.

at a minimum this needs new clasping hardware to be functional.
I have it closed with gorilla tape until I can figure something out.

PM me, I'll send new latches and black cylindrical shock absorbers, that should do the trick

 

[Mabett]

I installed mine today too @Mabett
The locking clasp needs to be better quality....Mine was bent and falling apart, had to use pliers on them....
And the tiny screws holding one of the pieces that blocks the wind fell out and I found them in the packaging...I put locktight on them.
I had to go around and tighten a few other Allen screws and nuts too....
For as much as this cost I shouldn't have to do this....
The table looks good and feels solid once tightened all down,except for the fasteners, you guys need to replace them....

PM me, I'll send new latches and black cylindrical shock absorbers, that should do the trick

 

[R1Bronco]

I received the new latches and installed them the other day....These are much better....The springs are strong on them and they latch securely now...Thank you @Mabett

Sponsored