Search results

Sasquatch with 37 ko2s. What is an acceptable amount of vibration/mechanical noise when running in 4a/4wd? I have maybe a 1.5/10 vibration when in 4a, very very very minimal and most likely others wouldn't notice it, and really only feel it over 50mph. Does not seem rotational (doesn't...

Put in a severe duty rack.. Any idea what I can do with the old one? Seems to be a waste to toss a good rack, also it's big enough to not want to save as a paper weight. Pretty sure you can't reuse it on a different bronco either...

Decided I didn't want to wait till 150k to do this, dealer wanted about $800 to do it so figured I'd DIY. There wasn't a whole lot of info regarding the bronco specifically, so I figured I'd add some info. Tools- 8mm pivoting wrench, 13mm pivoting wrench, 10 mm pivoting wrench 8,13,10mm deep...

Does anyone know the exact size of the hoss 3.0 or Severe Duty rack tie rod boot Clamps? I have a couple 2.0 rack clamps (the oem style ones) But I have a sneaking suspicion the 3.0 will need bigger clamps? I do not want to use worm style If I do not have to. Plan on picking up and installing...

Have Sasquatch with 70k miles. Would you go ahead and get new springs or reuse with the 6100s? Bonus- I now have 37s, do the 6100s limit stuffing at all compared to stock? Rubbing inner fender at full stuff (currently fixed with small body lift)

I installed a badlands disconnect 2 years ago on my big bend. Since then, every time the body shifts (flexing the front suspension or turning hard/fast enough) I get a single "pop". If the body shifts back the other way, I get a "pop". This ONLY happens if the swaybar is engaged (limiting body...

Figure I'd write a review- Truth be told I'm not super happy and previous anger demons came to life once I started pulling it off to recoat it. From the start-Installed the tailgate reinforcement and rotopax holder July 1st 23', shipping and ordering went off without a hitch, It showed up...

I'm trying to troubleshoot my electric stabilizer bar, hoping I can get some help. Essentially I added a oem stabar disconnect to my big bend. In the last few months I've been getting a popping sound when turning hard, it wont do it again untill I turn the other way hard (enough for some body...

I put a OEM disconnect on my big bend. I'm getting some type of pop/creak coming from that area when I get a little bit of body roll. For instance in a turn hard right it will pop. It will not pop again until I turn hard left. Same goes for things like turning into my hilly driveway. This...

I got Asfir underbody skids. After getting it dirty, and even after cleaning, I get a squeak and even minor popping when turning the wheel. I traced it to the 2 Skid mounting points right near the Steering rack. If I pop the skid off and clean all the mating surfaces, it generally goes away...

Looking for someone who wants cloth seats, and has MGV seats. I have the cloth seats. From a big bend with heated seats and manual adjustments. Figured with cloth seats no longer being offered, I may get someone. I am located in MN.

Not sure where to post this on the interwebs, but I'll be in Hot Springs 10-28-23 to run some stuff solo. Wouldn't mind tagging along with a group.

Since getting about 10k or so ago, I've had some type of minor vibration, very minor. Haven't worried about it much, but put new tires on and went about 1500 miles on a trip, it started to bother me. I'm pretty mechanically inclined, I fix most of our work trucks and am very hands on. Even...

Does anyone know what type of wire connectors/plugs are used on the sway bar disconnect? There are 3 plug ON the disconnect, and 1 from the harness to the vehicle side harness. It does not seem that you can order this harness by itself. Going to add a sway bar disconnect to a big bend and some...

Selling a AGS Air-Gate Compressor mount for the spare tire. Used from 2-25-23 to 7-1-23 Includes all parts from the kit. NOT PICTURED BUT INCLUDED: 8x bolts/ washers for the spare tire carrier, these are the ones that come from AGS- never used 8x extended bolts/washers for use with a tailgate...

Looking to trade my carpet flooring for your washout flooring. 4 door front and back. Could also throw some cash or trade. Could do the install also for both.

Theres a video floating around of basically using a Jack to compress the springs, undoing the top bolt, and lowering the jack to let the strut go free. It's a Toyota Video. Has anyone tried this on the bronco? How'd it work? Easy? Safe-ish? I understand it's not going to be as safe as an...

Big Bend SaS After added a Fab Fours stubby and Winch- I got an additional .5-.75" front sag. Total rake now is about 1.5". I'd like to raise up the front to be at about .5-.75"rake, and also bring the back up a bit, maybe an inch. That would essentially mean bringing the front up ~2" and Back...

I have a big bend, non SAS. Found that I may want to do more wheeling than I thought. For the thread purposes, I DO NOT want to get a new SAS bronco. Does anyone have a definitive parts list for doing a swap? I know I'll need to be replacing both axels. I think I'd go with 4.7 gearing. From...

Have been looking for a while now, figure I'd post on here. Looking for a Modular Bumper. I'm located in MN but would be willing to drive a bit.