Search results

No rubbing, no issues.

The covers fit around the headrest sockets real easy. So, I didn't remove them. The seat side levers-I worked around them. I couldn't get those off on mine. I was able to get the old and new covers on behind the plastics on the side. At this point, one of the other DIY posts may have figured it...

I apologize, I traded my Bronco in for a F150 2yrs ago. I didn't see that post. You don't remove the headrest sockets. The covers go over them and under. You cut a small hole and push and tuck under. In the photo below, the top one I already stretched around it. The bottom on shows the hole I...

Yes, your turn signals still work. Remember though, DRL works when not in Park gear and headlights off, i.e. daylight- "daytime running lights." Leave headlights in auto mode. During daylight, do the forscan change, set your park brake, put transmission in neutral, headlight knob on auto mode...

$250 *bump* someone with a 2.7L needs some boost in power

*BUMP* $300

Yes, but they went with the Bronco. Not required for use of the module.

bump

Traded my Bronco in this last weekend. Used for a few months. Panda claims up to 20% gains on 93 octane. Change setting on the fly via bluetooth. I ran 91 octane on setting 5 and definately feel a difference! Super easy to install, and leaves no trace on the engine computer. If this worked on...

I got them from a user on here. I believe they got them from CJ Pony Parts. Still going great after about 5k miles.

In Forscan I changed the configuration in BdyCM Module config (AS BUILT format) from this: 726-43-01 0202 0000 0176 to: 726-43-01 0101 0000 0176 0101 which is 'Turn and DRL'. Default was 0202 which was 'Turn Only'. 0303 and 0404 leave the position (marker lights) having priority. If there is a...

I also did the amber overlays from stickerfab. Then in Forscan I changed the configuration in BdyCM Module config (AS BUILT format) from this: 726-43-01 0202 0000 0176 to: 726-43-01 0101 0000 0176 0101 which is 'Turn and DRL'. Default was 0202 which was 'Turn Only'. 0303 and 0404 leave the...

I did the same.

Glad to see others doing it themselves too. Good job. I did mine out in the sun on a hot, humid day. I think it helped minimize my wrinkles. 👍

I have 726-43-01 set to: 0101 amber when driving, turns work, white when headlights on or trans in park 0202 is white, turns work (stock) 0303 amber, no turns 0404 amber, no turns I have a 21 big bend non-mid pkg w/signature headlights 0101 or 'Turn and DRL' is the only mode that works the...

This is with the Stickerfab amber overlay vinyl on mine. When the white DRL is lit, they look more yellow than amber. I like them though.

I didn't want to deal with heated seats. I'm fine without them. Not sure how big the heating pads are, but there isn't much room between the seemed areas of the seats. That's all hog ringed in place. I've never seen what the heating pads look like though. Leather, Black/Mahogany, I didn't order...

@Dads_bronze_bronco Front seats; -Two bungee straps under neath. You have to pop an electrical connector retainer clip loose underneath to get the strap loose. -You will see a black clip running along the bottom edge. -There are zippers on the back corners of the seats. The zipper slidder is...

No heated seats. I didn't want to make the install any harder. The pads would need to be pretty small to fit between the seemed areas where the hog rings are. I guess you could not hog ring the center, but I'm not sure if that would stay in place over time.

They were labeled as Black Mahogany when I got them. I got them off ebay from user 'sealeddeals.com'