Search results

Does using that power source still have the power save mode where is shuts off power 45-60 minutes after the vehicle is no longer running (like the 12v power port in the back does)? I'd like the option to be able to open up the back and turn on the light, regardless of when I last had the...

Where did you tap into the 12v source for the Kingpin lights? I'm going to do the same and didn't know if the 12V wiring to the accessory plug on the passenger side is the only 12v source to use. It looked like your liftgate wire went towards the drivers side - so that got me wondering if...

Just coming back to this thread to share the DV8 came back and after needing to provide photos (which included being able to slide paper between the DV8 box pieces) - they came back and suggest I go buy a $14 tube of sealant and apply to where their box and top lid come together. I'm thinking...

Can you share the footprint of the APL35 with the insulated cover? I'm having a custom slide made for it and looking to confirm the dimensions I need in the tray. I have clearance beyond the tray for the swing of the open lid - so i'm just looking for the footprint. Contacting Iceco directly...

Can you share a pic of this set up with the ladder. I have the roof rack and pax rax and am now looking for a telescoping ladder for roof top box access.

The grommets are installed and I actually cut and put my own heat shield on the exterior so that I didn't have cut outs for the grommets exposed to the elements. https://www.amazon.com/dp/B0B19SHCQ4?ref_=ppx_hzsearch_conn_dt_b_fed_asin_title_1&th=1

That's what I thought - but was looking to better understand where it covers/installs. If it just sits on top of the metal car body, and thus under the top plate of the DV8 box - I wasn't sure how it was addressing the gap between the top of the lower box and underside of the plate and car...

Can you tell me a little more about the SoundSkin in the cargo area - I didn't see that on their website.

The dust was pretty isolated to that cargo area and appears to have made its way in gaps to where the bottom bin meets the underside of the plate and cargo floor. I did not have dust around the OEM jack location in the floor. I was running with top on (hard top), windows up, doors on and cabin...

Revisiting this - I have the DV8 cargo area in floor storage box. Although I have the option to support the air compressor, I'm only using it for storage. I was on some pretty dusty trails this weekend and when I was re-arranging some items in that storage area, noticed that I have a coating...

To clarify - I have a late model 2024 year OEM painted top - which I'm learning has a few differences than the MIC hard tops - and I suspect the fitment of the accessory clip area molded into the top is one of them....

Looks like you have the deflecter in the highest position. Do your side brackets fit against your roof like in @adcam install pics?

Thanks for the pics. Looks like you have the deflector in the lowest position - which is what I did as well (but haven't tried to remove the center panel yet). Also, your side cut outs where the clips go is shaped differently on your top then on mine - which I suspect is a new design "feature"...

I just installed the Trailrax Half Rack on a 4-door - but haven't tried to remove the front and middle panels yet. I also installed it with the wind deflecter in its lowest position - but now I'm wondering if that was the best idea in order to not scratch the middle roof panel when removing it...

Just as an update - I have been in touch with Chris from Wicked Relics Offroad and am working with him on a custom fabricated tray that will mount to the top of the full cargo area tray to accommodate my fridge. He's been very responsive and informational - and I'm looking forward to working...

The Packhorse pull out tray (versus basket) is on my short list - but haven't seen too much about it when looking on Youtube or Bronco Forums. My Iceco APL35 is 27" deep - so I need options that will accommodate that depth - thus looking at the tray versus basket offering from WRO if I go that...

On the Raptor, it is a super easy install since I don't have the same exhaust and I could drop the bin in from the top. On a non-Raptor, the bin is put in place from the bottom (based on the videos I watched) and requires an exhaust bracket to be loosened to fit it in place and then reattached...

Yes, ToughBuilt is siimilar in concept to the Milwaukee Packout. A few key things that I considered going with them over Milwaukee - 1 - ToughBuilt is slightly smaller by width, and 2 will fit side by side in the back of the Bronco (Milwaukee will not). This was the biggest reason I went this...

Goose and AAL both make "system" floors that allow various add on mounting options for drawers, slides etc. Both sacrifice most or part of the access to the OEM in floor storage. I've replaced the platic molded in floor OEM box with the metal DV8 offering - nearly doubled storage in that...

From my research, it allows for full access to the OEM in floor storage, and a tad of extra storage under the top platform and behind the pull out when in its stored position (the pull out is not as deep as the full cargo deck). It also maintains the OEM tie down locations. My need for the...