Search results

On the website I see they recommend using soapy water to install any of the vinyl except the carbon. If you didn't do that, it would have helped a lot. I also installed them when it was low 50s temp. A hot day in direct sun could make everything a bit less forgiving. In person the 3D carbon...

My sneaker does grip on it good. I don't know about wet. I avoid using that area to step anyways. When decent frame mount sliders come out, I'll have a step. These are just added paint protection. They are textured as you can see in the close up pic. But they are a harder type of vinyl. Not...

I installed the StickerFab door sill protectors today. They went on good and were easy to reposition if needed. Zero bubbles. I went with the 3D carbon for maximum durability. For 15 dollars these are a cheap way to protect the edges on the door sills. The 3D carbon matches the diagonal lines...

I agree with the above suggestion. A MMD plugged in and using the screen in place of sync 4 is the first step. Next you would need to find a camera that can input to the device and an app that supports the camera. Maybe an old cell phone mounted inside on the far right of the windshield can be...

I'm not worried about the window wobble but I try not to open them too fast. To close them I use the black trim on the front doors and the black triangle on the rears. I use regular strength to close them.

You're the first one I've seen mention this on here. I feel exactly the same. The upper third of my back doesn't touch the seat. When I first sat in the Bronco it felt great, better than my old vehicle, but I didn't have enough time to notice this. The other day when I sat in my old car, the...

Make sure cruise control and lane keep are both turned off to get back to the regular sized speedometer and tachometer. This may be what you're asking but the speedometer will get bigger, not the tach.

Mic 2.0 4 door On top of open edges and honeycombing, now a popping/clicking sound started recently. In the area where the front two panels and mid panel all meet. It was only every once in a while. Now it's just constant. Super annoying... I've yet to try adjusting the various latch screw...

There are 2 hi-lift jack points built into each slider. They are meant to be used with an aftermarket hi-lift jack. I'm just not fully confident about jacking the truck like that on the body. Some after market sliders and bumpers have hi-lift jack points built in. Its mostly an offroad only...

I don't have them but I've looked at them. My thoughts are that it is still body mounted even though it appears to be a sturdy design. My worry is that using the jack points could cause damage in some situations. I'm still waiting on frame mounted. Fun-Haver is suppose to be coming out with...

https://www.bronco6g.com/forum/threads/%F0%9F%93%88-our-2021-bronco-order-stats-take-rates-after-3k-submissions.15803/ Here's something to get a general idea.

Haha got the email too. Would have liked one but my Bronco was built before anyone even started recieving these photos so I wasn't expecting to get one anyways. 7/15 blend

I actually don't think the amber LEDs are in the signature headlights' ring. But, I am hoping the amber bar can be turned on with parking lights in Forscan. A poster on here ordered ebay signature headlights for their base headlight bronco. The ones they recieved had warthog on a sticker. So...

Push for a repaint. My 2004 GTO rear bumper didn't match and a spot on the roof I noticed after a few weeks. It took three visits to the dealer and I got a little mad the second time. Third time they had a regional guy there to look at it closely and they finally agreed to repaint the bumper...

Got my first jeep wave yesterday. I waved back. Bright green lifted rubi. Not gonna lie. I liked it.

Thanks for the plug info! But now I know what it will look like when I take my plate off... I asked my dealer not to install and they said ok. It got installed anyways and they had a few bad excuses. My truck is, unfortunately, going in for body work in a few weeks. I was going to move the...

https://www.bronco6g.com/forum/threads/factory-fog-light-switch.22937/

From what I've read, the connectors will still be behind the mod bumper but the dial in the truck will not have the fog light button. You will need the new headlight switch with the fog light button and also you will need someone to enable the factory fog settings in Forscan.

I haven't seen that mixup yet but somebody did get some of their seats from a different trim.

🤞