Search results

I took off the skids and took some pictures and measurements. This is a side view of the frame member that holds the back of the front skid. You can see the height difference from the bracket that only lives on one side: The bracket looks to be 1 1/2 inches above the frame member: Here is...

Lights were not hard, just crimping connectors together once I figured out the connectors, and reordered the correct ones. (Don't look at the pictures, but read the description when you order from DigiKey). If I had to do it again, I might have bought the modular bumper wiring harness instead...

The picture of the Raptor engine skid was really hard to find. For the short term, I am going to put a 1 1/2 inch piece of square tubing between the Raptor front skid and the plastic engine skid with a longer bolt.. Once I buy the Raptor engine skid, I will fabricate a piece to replace the...

@flip was looking at the fame and noticed an extra flange on the Raptor. That made me recall something I had seen in a video: The blue flange is only on the Raptor, that is why their engine skid is the same height on both sides: The standard metal engine skid has one side higher than the other:

This is a good discussion on the lights. I need to update the discussion after my install: https://www.bronco6g.com/forum/threads/diy-raptor-fog-lights-installed-on-standard-bronco.71202/

It feels like aluminum. It is thick.

Bumper fits fine. No problems there even with the plastic extensions above and below the bumper ends. The Raptor front skid is a little bit of a challenge as the Raptor has two brackets on the frame, one for each side, for the rear of the skid, while non-Raptors have only one. I will likely...

Wildtrak 4 door: I have been playing with different grades of gas to see how it affects my gas mileage. I just drove 150 miles from Houston to Austin, so half flat, half hills. I filled up in Houston with 92 octane ethanol free gas (Bucees), because I had never seen ethanol free in...

Here is what the Raptor bumper looks like without the silver trim, if anybody is curious:

Has anybody installed the big silver aluminum Raptor skid plate on a non-Raptor. I have a question about bolt lengths. Back story: I was searching for a modular bumper and a Raptor bumper and skid popped up. Price was awesome. I am moving from plastic bumper and skids on my Wildtrak, so I...

I would definitely be in if the price was in that ballpark and assuming installation wasn't crazy expensive, warranty voided, etc.

I am also replacing the plastic bumper at the same time, so I am still getting to do some wiring harness fabrication fun. ha! With the plastic bumper it appears that the connector on the harness is an H11 type, so I have to create a pig tail that converts the 4 pin MX150 to two H11 connectors...

Great writeup. I literally ordered parts to do the same job last week. The light that I bought have the adapter that combines the two lights into one connector. The connector is just a 4 pin MX150 rather than 2, 2 pin MX150s. I will report back once I get my parts and do the install.

Bought early last month. Financed 100% with Ford Motor Credit to just leave the small town dealership quickly. With top tier credit, 7.95%. Refinanced 2 weeks later, after the registration was issued, with my credit union, 4.29%. I put half down, but they would have given me the same rate...

I am looking for one too, but with sensor holes. I am in Austin. (found one) OverLnd99, sent you a DM about one that won't work for me.

I have the Texas plates and registration sitting on my desk for my 4 door and it says: VEHICLE CLASSIFICATION: PASS-TRK BODY STYLE: UT I should put them on the vehicle, but then it won't be new anymore... ha!

Thanks for in the input. Will be tinting

Interesting. My drivers window only rattles if it is all the way up. If I crack the window it stops.

Summer is coming. Has anybody experienced summer without tinting the front windows, or is it just crazy to not do it?

Today I have received my 4th update in the last 3 weeks: 3.5.2, 3.5.3, 3.5.4, and today 22-PU101-MIL-LT. Still no 4.x version. I wonder if there are more than one revision of hardware that would have different major version numbers, or maybe I will continue to get these upgrades until I...