Search results

I just looked at Crutchfield and it says that neither the DCX 100.3 nor the CX fit in my 2023 Bronco. I saw other members say the same thing but I assume that you have to make minor modifications in the speaker cover for the protruding tweeter? Did you make any modifications to the speaker to...

Sounds good and thank you.....you may have given me the confidence to tackle this:) Do you have the B&O system in your Bronco? Out of curiosity did you replace all of your original speakers? Or only some of them? If you did replace them, what did you replace them with?

I will find the Bronco kit instructions as you mentioned but did the install require you to run wiring towards the front of the vehicle? or were you able to use the wiring where the factory sub is? I've been scrolling through the forum and googling this and mostly what I see is removing most...

I am still contemplating changing the sub and adding an amp when changing the speakers. I just looked at crutchfield and the JL sub that you used is no longer available. Any suggestions on a replacement? Just a beginner question....is that the factory amp between the mobridge and the sub? I...

wondering what speakers you changed? Just the front dash with the Hertz? or did you do all of yours? if you changed all of your speakers what brand/model did you install?

Hertz are the CX100? Who makes the C135L? What amp and setup did you add for the sub? If you wouldn't mind sharing exactly what you purchased for your final setup i.e. amp, connectors, etc. and is your speaker placement as follows? - CX100 in the left and right of the dash -CX100 in the left...

I assume you got the 300Hz base blockers from Crutchfield? And as I'm fairly new to the whole stereo thing are the bass blockers connected directly to the 2 front speakers inside the speaker cavity? Do you know what extra speaker wiring harnesses you got for the center channel? Were they...

Thanks for the info. I just checked Crutchfields website and it said that the Hertz DCX 100.3 does not fit my bronco. I have a 23 and it looks like you do as well. Did you have to make any modifications to the speakers to make them fit? If you do remember the name/model of the PRV speaker...

Been a while since I've done anything to my 23 OBX so I've recently been thinking about upgrading my headlights, tail lights and speakers. My Bronco has the B&O 10 speaker sound system. Been searching the forum and have seen a lot of very helpful information on speaker upgrades which seem...

Very nice. What side steps are those?

Just reading over your methods which I may actually do myself as Turtle Wax seems to have been out forever and they seem to make good products. Step #7 you mention is optional which says after step #5 to wait 24 hours for it to cure and wash car again and use the Turtle wax hybrid ceramic...

Thank you....been searching and it's almost impossible to find the correct part numbers. Any chance you could provide the part number for the plastic retainer clips circled in yellow. I broke one when trying to remove them to run a wire below. These are right under the hood as you open it...

Would you happen to know the part number for HM3? I stripped 2 of mine and am trying to find replacements. Where did you find the the parts diagram?

Perfect....thank you. Will probably order some with and without the washer.

Just to confirm before I place an order with you is that the HB3 (W721180-S450B) is the bolt below circled in red and is 30mm long and has a washer with it. The hole below circled in yellow that is missing the bolt is for the HB4 (W72221447-S900) and that is 23mm long with no washer.

Just realized I somehow lost a bolt on my front bumper. Are the bolts I circled in yellow the HB3 and the ones circled in red the HB4? The one circled in red has a washer and the one circled in yellow does not have a washer with it.

I have an Outer Banks with Sasquatch package and the standard running boards. I put Rockblokz XL on both the front and rear. Is there a company that makes something for the back end of the running board that will stop the snow/mud/salt/etc from sitting on the running board? I know either IAG...

I have this pre-bar bronco-prerunner-bumper-for-modular-bumper and am having the same issue....no light bar seems to fit. I looked at the 30" from Rigid and the 30" from Baja Designs and neither fit within the angle of the bumper bar. I even went as far as making a mockup with the exact...

Where did you purchase the Aeroskin from? Does the adhesion promoter and everything else needed to install come with the Aeroskin or did you need to buy anything extra? Just curious as I may consider buying this now.

How is the aeroskin holding up? I see you live in CA. I’m wondering because I live in NY and with the weather we get here I’m not sure how long the double faced tape would hold up. For the Oracle lights did you have to drill out and remove each letter in order to install the new backlit...