Search results

Yeah , its going to be nice , I am using a 7 port distribution air block and mounting that to the center of the bronco underneath onto the plastic shield around the fuel tank , so the lines are far away from exhaust pipes. The gas tank has a plastic cover all the way around it on three sides but...

got it from amazon , 1/4 inch braided loom , Pair it with the wirefly heat shrink , when you cut the loom , it will fray , so i slide the heat shrink over the ends and heat it and the adhesive seals the end from fraying more and seals the wire as well.

When I'm done , I will have 4 short 5 foot hoses , which I already have made up. They go from the valve stems , to where ever my hoses end up on each of the 4 corners of the vehicle. I have a 7 port air distribution block mounted underneath the chassis , Center port is the hose from the air...

So far all wiring done , compressor done , and stainless steel solenoid installed for deflation. Still have to run air hoses to the 4 corners and inside to a digital gauge but so far everything is working like a champ.

An led pad , or light pad.

Going to go out on a limb here and state , considering what you did go over. The ground clearance for bronco without serious major mods over stock sasquatch. You actually did pretty well. Comparing it to an extreme modded vehicle with 35's and just using the tires as a reference when its clearly...

This is one pad on inside the bronco at night. Yeah , I think it's bright enough.....lol. I also have a individual switch and a master switch hidden in the sunglasses holder. More to come when it's finalized

No thanks , I prefer to not have my food taste like or smell like burnt gasoline. I mean yeah , it's a thing but should it be really? I wonder how we are able to have people that are for environmental protection , protection of humanity and conservation of resources and then we have people like...

the switch i'm using supports 8 circuits , if you already have the upfitter switches you can omit the switches i used and use whatever you want on your upfitter switches. I used the molle overhead rail to allow me to do lots of other things , its sort of a universal design. You do not need it.

I mean yeah , amazon has tons of lighting options , you could do it without the Molle panel just would have to stick them above the windshield somewhere. You could run the wire from the LEDs down under the dash to an aux wire to your aux switches. It would be an all on or off thing though , can...

So I have been working on this with my friend Dallas. We come up with some pretty good ideas on things at work. We do a lot of custom fab around work. Being that the Bronco is a bit lacking in the interior lighting department, we decided to brighten it up a bit lol , ok more than a bit. So , I...

Buy a signal meter to measure decibels, its cheap and will let you know if there is a difference or not in an actual number. Phone app might exist as well. Just make as many variables the same , before and after. Like road surface , speed , wind speed and direction ( stationary ) in relation to...

While I applaud the look , I have to agree that grab handles out of paracord are much softer on the hands and less worrisome for any bumpy rides. If the manufacturers would think outside the box for use and not inside the box for money to be made. They would have wrapped the grab part with thick...

Slides in the track rail better lol

So if any manufacturers want to see how to make a rail system that uses more attachment points than the single point we got from the factory. My mod is far from professional grade but it is functional and very stable at any point a long the rail. So make this but make the full rail and it will...

I only had to make one part the rest was all store bought. Pretty simple to see what I did. Yeah. I talk about it in pretty great detail. I'll list the gear on it I used that I can remember. Amazon for almost all parts. Amazon.com: BRCOVAN Aluminum Alloy 1'' Ball Diamond Mount Base Compatible...

Love it , there is a thread I did about it in exterior mods. It's very very secure at riding rods , they hardly move at all.

The very first picture is equal to my eyes height and distance back. I'm 6 foot 3 inches.

The goal was to supply a better way of seeing information in a minimalistic way without having to look between the wheel. I also wanted it to be easily removable without leaving anything behind. I wanted it to be dead even with the windshield so that the numbers do not get skewed from one side...

I tried the dark mode in windows edge settings , not the website. I had no idea that was a selection. Most websites do not have that. Certainly dark mode would be the preferred default setting over what it is now.