Search results

It's all I had available to me, and narrower than I would like as well. I plan on updating it when I change the oil next.

So i'm sure you all recall the story about how Ford made GoodYear remove the Wrangler branding from the outside of the tire, but allowed GY to place it on the inside. So I was underneath mine trying to snap a picture of the 2.7L pulley/hose interference issue. Couldn't get a good pic of that...

I went and checked on mine, and it appeared to be touching the A/C Compressor clutch hub. When I felt its hose and braided covering it didn't feel like any damage had taken place, luckily so it was just barely clearing. I put a zip tie around it to keep it well away from the compressor. I...

Mine unloaded in Taft on Sunday and arrived at my dealer in Orlando on Tuesday afternoon. You'd think with the "volume" Mullinax supposedly has that they would be able to get trucks to ship vehicles to them, but who knows...

Mine was a dirt mountain parolee. It had 49 miles on it when I test drove it after it came off the truck and before they sent it to PDI. The sales manager was shocked. I wasn't given the distance to Dirt Mountain and the fact that mine needed to go to the MOD shop for B-O bar and stickers. I...

Just a final follow up, my Bronco shipped from Wayne on 10/7 and arrived at the dealer in Orlando on 10/19. So 12 days for this one.

@CO-Bronco you can change my status to Delivered because my parolee has made it home! I'm out to go get a 🍺but I'll be sure to buy you one when I get back for all of your hard work!🍻 And if you know of any extra "Dirt Mountain" stickers hanging around or where I could get some more made let...

After 100 days on Dirt Mountain my FE that was built on 6/29 is finally home! These first two picts are as it looked when it was unloaded from the transport truck. Not nearly as dirty as I thought it would be, but up close you can tell it has been marinating in a gravel lot for a while. The...

What I don't get is that the wiring diagram shows the turn/batt charge circuits coming out of the TRM and from there going through only 2 connectors to the trailer plug. It does not show the circuits going back to the BCM, which is what seems to be implied with the location of C201/C105. So...

No, don't do this. There is likely not enough current available. Do what Flip did earlier and tap one of the 2 12V lines where the TRM would have been installed on the left side of the vehicle. SBB91/SBBA7 in connector C4397A. These are both BU-RD. These do have fuses installed, even when TT...

It all depends on how long it takes to get a truck and put together a load for the dealership. On my orders it has taken between 2-7 days. I'm in this position right now as CSX unloaded my Bronco at the regional yard yesterday afternoon.

C4099 should be a standard Pollack RV style car end connector for a 7-pin trailer plug.

Definitely. Do you have the connector diagram that shows where connectors C105 & C201 are? C105 should have the reverse wire in it and we need to probe the car end of C201 to see if there is continuity to C4397C at the TRM. If there is, we'll just need the correct P/N for the harness that goes...

This is basically what I'm planning on doing initially. For the reverse light relay, I'd recommend using one that is diode-suppressed or soldering in a diode on your relay connector to prevent the reverse current spike from damaging the BCM. It may also be a good idea to put a relay on the...

Yep, she just needs to swap out those mall terrains 🩴 for some all terrains 🥾 and she'll be trail rated! :ROFLMAO:

Mine is going to ORL as well. Train car left Wayne at about 5PM on the 7th and made it as far as Cincinnati, OH as of this morning. I've had several Ford special orders come to this dealer. The ETA always is something like 3.5 weeks, and they have all arrived at my dealer in 10-14 days. The...

Mine did this the day before I got an email. It actually was completed and shipped that day. The fields on the Pizza Tracker didn't complete for another few days after I received the emails though but aemservices raw data showed the ship date and CSX TouchTrace confirmed my railcar (ID can be...

If you look at the price list that was posted, the Sasquatch package (765) is the same price manual or auto. Adding the auto to the build is +$1499 invoice +$1895 MSRP. So an auto sasquatch would be more than a manual. Someone at BN doesn't know how to read.

Got the railcar info from my dealer this afternoon, so it did ship out like the email promised. Currently passing through Wallbridge, OH according to TouchTrace. aemservices still not showing anything for release, shipment or transit dates.