Search results

Yes there is - if the top is still on, this makes it more difficult for someone to reach in and grab things from the back in a parking lot or such.

I'm considering making small plastic guide plates (probably 3d printed) to abut the frame and provide a guide notch to place the door edge in and push against and have a lever point to better control the door as you slide down so you aren't hovering while lowering onto pin. Before I spend the...

Well, at least the full shade I have won't work with the panels on - it hooks into the panel mount points for full coverage up front.

6 feet by 16 inches deep - if I had it to do over, I would space it apart from the wall by a 2x4 for two reasons - it needs to be just a little deeper and to leave a gap between the shelf and the wall because the window rubber seal sits a little below the flange/shoulder it rests on (or cut a...

I want to replace my wood cross-member and hooks with angle brackets like the recent post above but this is working REALLY well for me so far. I can do it myself in 10-15 minutes including roof panels. Shelf folds flat against wall. I didn't leave myself as much clearance at the ceiling as I...

So does the MPP - comparison charts show they have better coverage, but the only drawback (and I've experienced it) is it is only good at Berkshire dealerships. I'm looking to see how the cancellation refund works.

I have Berkshire Hathaway MPP - it was only $1761 at time of purchase but I tried using it the other day and it didn't work outside the BH dealer network and couldn't use my rental car coverage. I'm considering cancelling and getting a refund - why is the FordProtect so much more expensive?

do you still have these? Price drop?

I still love my Bronco but I'm really starting to despise FORD! So I finally got great help from the OTA team and after an hour or so they put me on a 3 way call with Ford customer experience and a dealer they found in my area - they confirmed that any loss of contact with the vehicle would be...

I spoke with Ford and they told me something has happened to block their OTA connectivity and I'll have to take it in to the dealer. This stinks. I can't afford to be without my daily driver and no one has service vehicles anymore. Last time I took it in I had an appointment and it turned out...

Mine looked like it already had a setting with that within. But, doing all the others resulted in a ABS error. It says "incompatible configuration" or something like that. So, I reset the error and went back and changed the other settings back. But, the error is still there.

My 760-03-01 doesn't start with B. I think it started with an E as I recall. Should I still change it?

I can't find the 360 camera calibration in Forscan- it only lists lane departure camera calibration.

something I haven't seen noted very often is, besides the fender flares themselves, the SAS package has what appears to be little "mud flaps" mounted to the rear bumper to bridge the gap between the bumper and the flare. That seems pretty important for aesthetics and functionality. I haven't...

Oh, I thought you indicated you built your bumper itself.

That's very clean - how on earth did you make it? Did you document your process? I'd love to see that work.

Very cool - I grew up in Tyler and bounced around family in Athens/Palestine/Tyler area and later Texarkana. God's country!

That's great. Nice video. First, what part of ET? (I'm an ET boy). Also, what drone and how was it controlled?

I wish I'd seen this a week ago - I passed on a great tire/wheel set of takeoffs because they were SAS and not WT - I'd have bought them and traded with you. I found a good deal on just the wheels but would have preferred the whole set. I'm sure. you'll have no trouble finding someone to swap...

I saw a review of the KO3s and it looks like they made some great changes - but, it rains a lot in Houston and I have found the KO2s quite good in rain. I have 20k miles on them - maybe that will degrade, but so far they're comfortable and stable and climb rocks quite well.