Search results

"Branded tool kit." This has me very curious what it is. (The tool roll that has been out for a while?) Interesting that it's not listed with all trim models, and is not available with side steps? Same with the jumpstart kit. Battery Jumpstart Kit Note: Not available with Side Step (18D)...

Thanks, this is what I needed to know. I'll have a minor amount of disassembly to do. Too bad I can't just install the new camera myself.

My question is where does the camera connect to the wiring harness. Is it outside the vehicle at the camera, or inside the vehicle.

I kind of wish you had not posted this. I have the Broaddict panels and WANT the slide out tailgate. Now I know they are compatible...

I just got notified that parts are in to replace my recalled camera. Assuming they actually replace the camera, how far does the harness go before it plugs in? I'm hoping the connection is at the camera. Otherwise I may have to remove some modifications.

Thanks @WolfBox for giving me the chance to try this duster out. MF200. (Think Samuel L Jackson when you say it.) This is the magnum version of air dusters. Three settings. On high it’s a little leaf blower. I’m pretty amazed at how powerful this thing is. It can be used to sweep from a...

I can say it worked for me. I actually set it up with mykey restrictions in the unlikely event i might let my teenage son drive it.

I kept one of the fobs from the Bronco I crashed, and reprogramed it as a third for the one I'm driving now. it was 2 years ago, I barely remember doing it. I followed the instructions in the owners manual.

ARB (dual brushless compressor) instructions. See pages 25 and 26. It calls for 6 gauge, but you can't go wrong going larger. Adding a bus at the rear for other equipment is not a terrible idea. https://store.arbusa.com/content/CKBLTA12 INST.pdf

I’ll see if I can get pictures when I get home from work today. If you take the floor up, should be easy to find. You can also see them from below.

There was a post a while back from a guy developing a system to store and dispense water from inside the tailgate. I'll post the link if I can find it. Edit: Found it. https://www.bronco6g.com/forum/threads/spy-shot-next-eos-bronco-product-drop.119406/

There are small grommet plugs on both sides of the storage (tool) compartment, close to the wheel wells in the floor of the cargo area. I would go this route before I would use the drain plug. This is how I got a wire to the rear bumper.

I installed mine by myself, without having to drop the tank or support it with straps. It was a little tricky getting it balanced on the jack. Run the tank as dry as possible. Loosen, but do not remove the bolts for the straps holding the tank in place. The packing material makes good blocks to...

I originally mounted mine on the roll bar. This worked excellent until I put my top on. Then I couldn't see more than one car length behind me. So I relocated it to the spare tire with a AGS mount. I"m going to change it, right now it's more of a semi permanent mock up done with what was handy...

This has been on the list of things I want to do for my Wildtrak if I can match the stitching color.

https://store.arbusa.com/pressure-control-0830001 Bluetooth pressure control.

It created the front from previous renderings, this is from a side shot that did not show the winch. Scary.

Only time will tell. The weak spot is the connection to the fender. I’ll keep an eye on that, especially since it shares the mounting point for the module below. The KR mount is thick enough I doubt it would fail. Hopefully there won’t be much (if any) flex. I didn’t know it mounted to the top...

I just installed the brushless twin on the KR mount. Seems pretty solid to me. Also installed the Bluetooth pressure control. Ran a hose to the front bumper so I don’t have to open the hood. There are several posts I referred to that really helped out. Overall, it turned out very clean. My...

Hopefully they will reduce the price for the transmission skid separately like they did for the fuel tank.