What did you do TO / WITH your Bronco today? 👨🏻‍🔧🧰🚿🛠

[mikeb614]

I built a custom jack block for my floor jack to reach the proper jack points of my Bronco. The block is glued and pinned from good quality plywood.

Sponsored

 

[dpAtlanta]

I built a custom jack block for my floor jack to reach the proper jack points of my Bronco.

Take a Sharpie and neatly write:
"Conforms to OSHA 29 CFR 1926.305"

 

[AZ_Craig]

I turned mine into a Raptor! Best way to make 3 active recalls go away!

went from this

You already had Raptor lights. It basically was a Raptor .

 

[jeffreybehr]

I built a custom jack block for my floor jack to reach the proper jack points of my Bronco. The block is glued and pinned from good quality plywood.

GREAT idea and work; TY for posting.. My smaller, aluminum jack from Harbor F. Tools decased ago sitll works well, but it doesn't have a dished pad like yours--it's a flat, rubbered pad.

 

[jayr1959]

Replaced the carpet storage cover with the washout cover.

 

[Sitruc_btb]

Working on some chase lights. Need to finish the wiring.

 

[lwilliams34]

Cleaned and applied adams protectant to Ford OEM floor mats.
.

 

[lwilliams34]

Installed IAG Rear Cap Rail Protectors. Fitment and function is top notch.
.

 

[lwilliams34]

Installed Smart Home Lifter in Garage for removing the back cap.
Instructions were pretty straighforward. Biggest challenge was getting the lift rails level to balance the weight of the cap.
.

 

[mikec426]

Replaced the carpet storage cover with the washout cover.

Who makes that?

 

[jayr1959]

Who makes that?

Ford part number M2DZ-9813046-D it was $636 shipped.

 

[Dmesser92]

Dropped mine off at the dealer to have some warranty work done.

 

[Whiskey Bizness]

Damn I'm tired.. At 81YO, slightly arthritic, and 40 pounds overweight, and with the temp. in the shade about 100dF., that tire work took me over two hours--I rested in front of the cooler quite often--and my younger, healthier, stronger neighbor again had to lift the spare onto its mount.

While you were doing all of that, there were 81 year olds sitting around wasting away! Keep after it! I'm 29 years behind you and hope I've got that energy and drive when I'm 81.

 

[jeffreybehr]

While you were doing all of that, there were 81 year olds sitting around wasting away! Keep after it! I'm 29 years behind you and hope I've got that energy and drive when I'm 81.

TY.

 

[stampede1]

Yesterday, my 3rd day of ownership, I rotated the 5 original tires one position clockwise and today changed the engine oil and filter.. My stealership uses some greasy black crap on tires that is NOT water soluble so has to be scrubbed off using a houshold cleaner; the first 3 I scrubbed with much detergent before realizing I wasn't getting much off , but the last 2 are relatively greasless and look better.

Engine has 3250 miles on it; used Kirkland full-syn. 5W-30 and a FRAM Ultra Synthetic filter.. The skidplate is fastened to the chassis with the same 15mm-hexhead screws as my Badlands was and came off and went on very easily.. Also replaced the throw-away panplug and replaced it with one of those pricey, permanent, machined-aluminum versions.

Damn I'm tired.. At 81YO, slightly arthritic, and 40 pounds overweight, and with the temp. in the shade about 100dF., that tire work took me over two hours--I rested in front of the cooler quite often--and my younger, healthier, stronger neighbor again had to lift the spare onto its mount.

But I LOVE LOVE LOVE this thing--even the Raptor bling.. It's much more responsive than the new Badlands I owned for 18 days.

You are 81 going on 29, well done sir! Wish we could all be so lucky at your age!

Sponsored