What did you do TO / WITH your Bronco today? 👨🏻‍🔧🧰🚿🛠

[OkieB6G]

https://www.hydrascapestickers.com/

Awesome, thanks! Mind sharing which size you went with?

Sponsored

 

[604Bronco]

Finally got my circuit board and code work completed for a custom lighting project. I'm using the @ORACLE Lighting back-lit letters with an Arduino micro controller to animate things. Here's a quick shot of the unlock sequence.

Alright, I'm not for the light-up Bronco badge, but this looks awesome. Well done!

You should definitely sell these and/or do a write-up about it.

 

[jcgcbns22]

Clay bar, sealed, door sill protectors installed, old-school Bronco script on front quarter panels. Next up will be the hitch and 4-pin harness.

Haven't pulled the trigger on lights yet, but grateful for input. Looking at BD, DD, and Heretic.

I am awaiting install due to my bill bar being in transit but check the spec and pricing on Teralume Industries ICON lights. Impressive. Arrived in less than a week from Oz. Ordered their pillar lights today too.

 

[zane8stacks]

Awesome, thanks! Mind sharing which size you went with?

full size infinity, and i still had to cut some off on the left hand side so i could center mountain. i had it wrapped into vent on left side and its wrapped around the right side to the vent

 

[OkieB6G]

full size infinity, and i still had to cut some off on the left hand side so i could center mountain. i had it wrapped into vent on left side and its wrapped around the right side to the vent

Awesome info, thank you! I'm going to give it a shot.

 

[JDoc92]

Turned a phone mount into a radar detector mount.

 

[Bronco-ocnorB]

Clay bar, sealed, door sill protectors installed, old-school Bronco script on front quarter panels. Next up will be the hitch and 4-pin harness.

Haven't pulled the trigger on lights yet, but grateful for input. Looking at BD, DD, and Heretic.

Can you share where you got those door sill protectors? They look really nice and would go great with Carbonized Grey!

 

[BroncoScott]

I took the fam out to Crescent Beach in St. Augustine Florida this weekend. This was my first time driving on a beach and let me tell you, it was cool. I got to show off the Bronco while not having to lug a bunch of beach stuff from some distant parking lot. I love it.

 

[p3pete]

Can you share where you got those door sill protectors? They look really nice and would go great with Carbonized Grey!

Can you share where you got those door sill protectors? They look really nice and would go great with Carbonized Grey!

Stickerfab.com. Like 15 bucks.

 

[Tricky Dick]

Finally added the dash top USB port (A and C).

I like this setup but didn't want to lose the functionality of that little pocket. Got this little guy instead which measurements say will fit right here. I'll have results in about a week.

 

[imaginager]

I like this setup but didn't want to lose the functionality of that little pocket. Got this little guy instead which measurements say will fit right here. I'll have results in about a week.

I looked at those, as well. Couple of things; it requires a USB A port to plug into and I wanted something hardwired (although I could have hardwired a multi-port behind the glovebox and plugged it into that) and I was concerned I'd never be able to remove it (due to those 4 teeth) once installed. Also, needed the USB C.

Will be watching for your install, though, as I do really like that location on the dash - you could plant multiples of that style port, which would really work well with some the AR BYOD mounts I've seen.

 

[Tricky Dick]

I looked at those, as well. Couple of things; it requires a USB A port to plug into and I wanted something hardwired (although I could have hardwired a multi-port behind the glovebox and plugged it into that) and I was concerned I'd never be able to remove it (due to those 4 teeth) once installed. Also, needed the USB C.

Will be watching for your install, though, as I do really like that location on the dash - you could plant multiples of that style port, which would really work well with some the AR BYOD mounts I've seen.

I was actually hoping to find one that was USB C. Instead I'll just use an A to C cable for my charger. I'm just going to run the cord down to the plug in the console for now, but if I like how it turns out I'll probably buy a second one for the other side and one of these to power them. My thinking with putting them in the removable "accessory ready" part is that I can pull the whole assembly to pop the ports out, or even easily replace that part completely to go back to stock.

 

[zedster]

Installed the Husky cargo liner in my 2 door.

 

[Amcole1984]

Installed my Bad Bronco skeleton emblem today. I ordered carbonized gray touch up paint and painted over the skeleton to make it pop a little.

 

[NKovo11]

Clay bar, sealed, door sill protectors installed, old-school Bronco script on front quarter panels. Next up will be the hitch and 4-pin harness.

Haven't pulled the trigger on lights yet, but grateful for input. Looking at BD, DD, and Heretic.

are your script decals Bronco Depot? and did you have to trim them at all to fit them in that spot? thats where i've been wanting to put mine and keep the OEM badging but haven't seen anyone try it yet!

Sponsored