🛠 1/3/22 Build Week Group

[Roger123]

Still not use to the window buttons being in the middle. The passenger side seat not sliding forward with just the leaver on the back of the seat. Have to change the mode back every time on the dial you restart the Bronco.

Are you sure? Ours does.

Sponsored

 

[daddycreswell]

Are you sure? Ours does.

Mine doesn't do it, or at least I can't make it do it. I'll have to look again tomorrow. Are you using the shoulder leaver or the side?

 

[Alvin Olson]

They look great!

Personally, I always gauge my projects on the number of expletives I hurl. My wife usually goes and stays with her parents for a couple of days when I announce a new project…

preaching to the choir.
it was marital touch n go there for a bit.

 

[Bird Dog Off Road]

No I didn't make patches @Bird Dog Overland did.

I only did stickers. Someone was doing patches.

 

[Dheritage]

I only did stickers. Someone was doing patches.

Bird dog are you going on all terrain nation tomorrow night?

 

[Bird Dog Off Road]

Bird dog are you going on all terrain nation tomorrow night?

Yep, 8pm cst

 

[Dheritage]

Yep, 8pm cst

Good luck I tune in normally every week

 

[OkieB6G]

Night shot of the lights
Hard to capture the light but here you go.
I will say the white is bright!!
The ambers are perfect for DRL

Thank you!! I am sold on these. They look fantastic in the modular bumper cutouts, and after seeing how bright they are, I think I need them.
Adding those to my birthday wish list...

 

[Roger123]

Mine doesn't do it, or at least I can't make it do it. I'll have to look again tomorrow. Are you using the shoulder leaver or the side?

I didn't think either side did it at first but I was able to get them both to do it. I pull the lever by the shoulder to fold the seat forward then I use my hand on the back of the seat to give a better push while holding some tension on the shoulder lever.

I found it was difficult just using one hand on the shoulder lever. I think the seats need to break in a bit, it's gotten easier the last few days. The seat back needs to tilt forward enough to release the slid latch, if that makes sense.

I was pi**ed at first thinking they didn't operate like every other 2 door seat in the universe. I actually told my wife how stupid the seats were but then I messed around a bit more and got them to work.

They go right back to the pre-set position as well. I just push the seat bottom back first then the seat back, works like a camp.

Give it a shot!

 

[Cszmom]

Monday morning update….still no update! Still stuck in production, still EDD of 2/10 which is impossible since it can’t get to DE in 3 days

 

[Panmort]

My train already crossed into Mississippi and isn't too far from its final destination in New Orleans.

 

[Sanner]

Monday morning update….still no update! Still stuck in production, still EDD of 2/10 which is impossible since it can’t get to DE in 3 days

very similar here… 01/06 production date… 02/12 projected delivery… nothing changed over the weekend. I’m in Pennsylvania… about 4.5 hours from MAP… I’m kinda holding my breath… but squeaking air in from time to time

here’s hoping my friend!!! Blessings!!!

 

[Alvin Olson]

Thank you!! I am sold on these. They look fantastic in the modular bumper cutouts, and after seeing how bright they are, I think I need them.
Adding those to my birthday wish list...

The install isn't complicated, but it takes some time and patience if you do it your self.
The parts arrive in a small box and you have to use your Erector Set skills to assemble the lights into the bezels. Make sure to order their wiring harness for I think an additional $20 as it is pre measured to fit.
You will need a crimp tool, some wire strippers and a heat gun or lighter to seal the butt connectors.
You will also need small arms to route the wires. Watch the 2 videos he links on his web site and the instructions are helpful to know what wires to connect to for the switches.

 

[TheRealRacingX]

very similar here… 01/06 production date… 02/12 projected delivery… nothing changed over the weekend. I’m in Pennsylvania… about 4.5 hours from MAP… I’m kinda holding my breath… but squeaking air in from time to time

here’s hoping my friend!!! Blessings!!!

We're all in the same purgatory boat I feel.... I have a 1/6 production with an EDD that updated to 2/10 on friday.... I live in western NY, about 4 hrs if you go through Canada

 

[Cat]

I only did stickers. Someone was doing patches.

@1979

Sponsored