direct wire harness LED fog lights modular bumper

[SPVPARTS]

Ahh..yah. Thanks for being helpful with great customer service.

Always happy to!

John

Sponsored

 

[roidragejd]

I will break this all down. Hopefully this helps others as well.

For those who are converting their Broncos with a take off Bronco Raptor Bumper... OR Those who are swapping fog lights from a Bronco Raptor Bumper-

Here is what you are running into...

There is a harness installed in the bumpers that is unique to the trim level of the truck the bumper is on or came off of.

The harness will have connectors for Parking Sensors, Adaptive CC and Fogs if they are on the truck.

That harness will combine to ONE large Molex connector that plugs in just behind and at the base of the driver side wheel well liner.

When you swap bumpers, you generally want to take your bumper harness off in case you have different pieces on the bumper (Like parking sensors, adaptive cc, Fogs, ETC)

Hopefully you can all follow this because it may get a little more confusing...

If the truck itself, originally had a standard bumper with fog lights or a capable bumper with fog lights... Your stock harness that is on your original bumper will have H11 connectors for the ONE fog pair... You will want to KEEP and transfer that harness from your original bumper over to the conversion Raptor bumper...
This is what the H11 matching connector adapters look like-

https://www.specialtyperformancepar...-pair-see-details?_pos=1&_sid=4bc717dbe&_ss=r

https://www.specialtyperformancepar...ystem-see-details?_pos=2&_sid=4bc717dbe&_ss=r

https://www.specialtyperformancepar...s-w-many-vehicles?_pos=5&_sid=4bc717dbe&_ss=r

If you are converting a NON Raptor version to have a take off RAPTOR bumper. You would want this H11 Adapter to Molex-

https://www.specialtyperformancepar...-bronco-to-raptor?_pos=3&_sid=4bc717dbe&_ss=r

And then this Molex Splitter which would combine BOTH Pairs of the OEM Raptor lights into the ONE connection you have.

https://www.specialtyperformancepar...-pair?_pos=1&_psq=molex+splitter&_ss=e&_v=1.0

You could also get a single pair fog harness to run up to the switches if you prefer for the second pair here-

https://www.specialtyperformancepar...ails?_pos=1&_psq=single+pair+fog&_ss=e&_v=1.0

With these matching adapters-

https://www.specialtyperformancepar...etails?_pos=4&_psq=molex+adapter&_ss=e&_v=1.0

Or if your truck never had Fogs at all you can get this OEM Raptor fog conversion harness just to the aux switches-

https://www.specialtyperformancepar...ss?_pos=1&_psq=conversio+harness&_ss=e&_v=1.0

The Main reason you want to take your original bumper harness with you is because some of your stuff may not match.

If you have sensors and adaptive cruise. You may be able to use the built in harness if it is still on the Raptor bumper, but the way it was configured is, the one pair of lights (with covers) was on Aux 1 and the other pair was on the fog switch. When you plug it into the truck, there is a mismatch because NON Raptor versions do not have the Aux 1 wire run down through there so that line would be DEAD. Only the Fog switch connection would have power.

That pretty much covers the "Bumper Swap" situations.

Next, lets talk about the Bronco Raptor Fog swaps and their original connectors. (There may still be some crossover)

The connector you show in your photo is a PRE connector on a Raptor Bumper Fog pocket. Because Ford wanted assembly to be faster, they have a 2 connector pig tail behind the back cover of the housing that merges to the ONE 4 pin connector you are showing there.

Here are photos of an OEM Fog housing, with cover removed and of the Pig tail harness. You will want to RETAIN and REMOVE that harness if you are trying to swap lights or access each pair. Because the adapters are to connect to the 2 pin Molex connectors..

If you LOST or need a replacement. We have a couple CUSTOM ones available. You can reach out to us.

(Photo of custom produced Pig Tail )

From there... What plugs into those would be the MOLEX Fog adapters... Here is a link-

https://www.specialtyperformancepar...ns-squadron-s2-s1?_pos=6&_sid=fba08c4a7&_ss=r

https://www.specialtyperformancepar...es-diode-dynamics?_pos=9&_sid=fba08c4a7&_ss=r

https://www.specialtyperformancepar...dynamics-radiance?_pos=4&_sid=fba08c4a7&_ss=r

https://www.specialtyperformancepar...ynamics-radiance?_pos=22&_sid=c8c195c53&_ss=r


So with this, you can plug into the Fog switch and the Aux 1 (if the truck is a Raptor)

Hopefully this helps...

John
SPV Parts
info @spvparts.com
317/934/6778

I need one of those custom adapters. And then a plug that goes from one of the 2-pin ends to just a wire I think. I have Baja Dutch lights that I need to move to AUX1 on my raptor (I sold the factory’s bumper and didn’t take the wires) so I have jsut that 4-pin behind my new bumper.
I don’t see that custom pigtail on the website tho?

 

[SPVPARTS]

I need one of those custom adapters. And then a plug that goes from one of the 2-pin ends to just a wire I think. I have Baja Dutch lights that I need to move to AUX1 on my raptor (I sold the factory’s bumper and didn’t take the wires) so I have jsut that 4-pin behind my new bumper.
I don’t see that custom pigtail on the website tho?

We may have already talked with you. Since they are actually included with take off lights. We actually custom made those. So if you need them, they arent on the website. Just email or message us.

John

info @spvparts.com

Sponsored