Search results

does anyone know the main piston size for these falcons? The travel numbers claimed and adjustablity looks great but I can't find if they are something like a 60mm like other equivalent 2.5" body shocks that these are marketed against (fox/king/Icon/ADS/etc). The travel and aluminum body for...

1. Correct no provisions for fog lights so what I did is made some jumper harnesses that go up each side of the engine bay and I mounted my 3x3 amber cube lights (I had replaced my factory fog with those) on the mirrors for ditch lights. 2. You'll have to remove the main grill, headlights...

That light bar is an extreme LED brand bar. It's all one assembly, ambers on the outside for one circuit and spot white lights in the inside https://extremeledlightbars.com/x6s-all-amber-and-white-lightbars

Thanks for the reference photos! I was thinking the same thing, cut them back just a bit and weld on end caps. Turn off-roads truck in their product photos shows they did similar I'm still on the fence about modifying the crash bar horns in the event on collision and insurance...

agreed to both of you.. Times I look at it and I think bumper loosk great, don't even see the crash brackets. Other times its all I notice. I think it comes with the territory on any high tuck bumper. ADD, SVC, SFR, JCR crusader. I've looked at them all by this point and its just par for the...

Just installed my hyperlyte front and did a quick writeup https://www.bronco6g.com/forum/threads/turn-offroad-hyperlyte-front-bumper-installed.109094/

hey guys, @Turn Offroad early this year released a new series of lighter weight bumpers for the bronco trying to cover the other end of the spectrum from a lot of whats offered (giant heavy winch bumpers and bull bars). I personally like using my truck for a lot of higher speed offroad and...

The holes in the outside most edges of the skid plate look like they accommodate the low trim (plastic skid plate) tow hook/intercooler combo brackets. I picked some up off eBay assuming that's the case. My brackets are different with the capable bumper/steel skid plate

Bit the bullet and ordered the hyperlyte front. For this price point it seems too good to be true so I'm a bit concerned over the coating quality and material thickness but all the factory plates and bumpers are 1/8" / 3mm too so hopefully this is just a really well made affordable bumper

The hyperlyte series looks exactly like the Baja style bumpers I've been wanting. My only question is what happens to the grocery points? No provisions for front tow hooks?

RCV has always been pretty vague about their OBJ/IBJ plunge and angle capacities but I think the strengthened 300M bearing cups give them strength to avoid breakages during over travel. It's just a very overkill solution if you are trying to address a low load high angle scenario like full droop...

I had not seen that broken innovations kit before, that looks by far the best engineered of the bunch and moves all three mounts. Most I see don't do the pinion mount and tip the axle down. Probably a bit too much drop for address a mild 1" curb height lift over stock SAS and the extended...

Hey everyone, I've been looking at what coilovers to go with down the road when my HOSS 3.0 Fox 2.5's wear out or I'm just ready for more travel. I'm pretty set on King's due to what seems to be their best overall travel numbers comparing compressed/extended lengths. Multiple sources (mainly...

Ya I put them in. Pulling struts on the bronco sucks, you have to touch every bolt. I was hoping to just break the top ball joint loose but the shock studs are so long you have to pull the LCA bolts too and get an alignment. Also the springs need a lot of compression to take pressure off the...

Hey guys I actually just put on an RPG 1.5" collar on the front only. It sits 1/4 high in the front verified by measurements on fender heights and running board heights. So slightly higher than level but hey more front jounce travel and bit of a prerunner look