What did you do TO / WITH your Bronco today? 👨🏻‍🔧🧰🚿🛠

[Bigshep]

I took pictures of the new cracks in my Bronco top.
I will likely look into getting the top done in something similar to Line-X
Since there are so many horror stories about getting the top replaced under warranty.

Sponsored

 

[Ninjak]

Pretty much done with the revamp that started with a bare Armadillo top and a final decision between lime pearl or orange pearl on the repaint

I think I made the right call.

Oh, that's looking good! Look forward to seeing it next month. I'll see ya there. Looks like we are going to have an Armadillo section! lol.

 

[Hammerli22]

My kid and I designed, printed and installed these. With the top off if nobody was back there the seatbelts smacked against the pillars. These will hopefully stop that.

Installed with 3M molding tape. Two strips and I was sure to shake it while saying "she ain't going anywhere" to ensure she doesn't go anywhere.

He's going to upload the files to makerworld. I'll post the link in the 3d printed thread when done.

What's it listed under, I saw another one on make a world that has a Bronco logo is that yours?

 

[Fastmc25]

Painted my recovery loop today. Waiting on the other one to get delivered by UPS today. Then I’ll get it painted and installed

it’s a slow day

 

[Gbauer]

What's it listed under, I saw another one on make a world that has a Bronco logo is that yours?

Nah. He made it himself and didnt put a logo on it. Hes just learning so its pretty basic.

He signed up fir thingiverse yesterday but they have a 24 hr wait period before he can upload the files. Ill give a link when he can upload them.

 

[lwilliams34]

Had my annual ceramic coating maintenance done today.
Saw a Corvette C8 Z06 up close...
.

 

[MikeOBronco]

Sold my 23 2dr Badlands today. Replacing it this summer with a Raptor...not sure which one yet. I have a Top Lift Pro for the 2dr, Grey BroncoBikini top and a bunch of 2 dr Badlands takeoffs that I'll post later in the marketplace at cheap prices.

 

[BattBronco35]

Got the Bilstein 6112s and Icon UCA installed today. Man does it look great AND love the ride so much more. Pretty much bang on 2 inches in the front and like 1.5 rear. Ended up not needing a new rear Trac-Bar

 

[CDub from the OC]

FabFours bumper, warn winch, rigid fogs and light bar, Bluemak 3D ditch lights.

 

[JiuJitsuJoe]

Put on rear lower control arm skid plates from Turn Off Road

 

[cynicalrider]

Couple random adventures with the family.

Random NJ snow storm:

Untitled by MJH Creations, on Flickr

Went up to northern VT for some snowboarding. Camped in the parking lot and then we tried to make it to my buddies property in southern VT. Problem is the road he is on only gets plowed to the one house on it leaving a massive snowpile to get over and then unplowed road after that.

We dug out and flattened enough to get over it but the snow after was impossible to try to get the next 1/4 mile to camp. But of course then I was stuck on the other side so a bunch of winching and digging to get back out. Eventually just camped at the snow pile.

Untitled by MJH Creations, on Flickr

Untitled by MJH Creations, on Flickr

Untitled by MJH Creations, on Flickr

Untitled by MJH Creations, on Flickr

Untitled by MJH Creations, on Flickr

And then a small hike with the fam with a PA water crossing on the way home.

 

[DGE1993]

Wrapped up my M190 to M210 swap. Moving on to re-gearing the rear axle next.

 

[Gbauer]

What's it listed under, I saw another one on make a world that has a Bronco logo is that yours?

https://www.thingiverse.com/thing:7315474

He just uploaded it.

 

[Jakethesnake]

Added a rough country tubular rear bumper. Not a hard install once you learn to decipher the crappy instructions.
Having trouble with the license plate relocation light. The wire is way too thin a gauge and is hard to work with.

Looks good in my opinion and feels pretty solid

 

[Reddout99]

Added a rough country tubular rear bumper. Not a hard install once you learn to decipher the crappy instructions.
Having trouble with the license plate relocation light. The wire is way too thin a gauge and is hard to work with.

Looks good in my opinion and feels pretty solid

Looks good and follows the body lines pretty well.

Sponsored