What did you do TO / WITH your Bronco today? 👨🏻‍🔧🧰🚿🛠

[Ground_zero298]

Just a strip tease today.

Sponsored

 

[JHawk]

Installed this- Element E50. E100 going up front.

What are the holders that you are using for the Element?

I figured it out Quick Fist with some bungees.

 

[JHawk]

Awesome, where is this?

 

[Jmor]

Devils Tower, Wyoming
My Close Encounter of the Third Kind

 

[tongsun3717]

Awesome, where is this?

Monument Valley, AZ. Thanks!

 

[Ground_zero298]

Took her to work today half naked. Was a running around day. I can say this has been the best set up so far. Test was done with doors on. Will check with doors off in the future

With the windows up the cab is dead air movement wise.

With the windows down you get a breeze on the back of your neck kind of just rolling on your shoulders. Even felt good on the Highway.

Hit 99 here today in Michigan (gp area) ac works great with the top like this. Nice blend of cool air mixed with the fresh. Was comfortable the whole day.

I’ve read others on here worried about losing a top. Well I can verify the tops are stable to 100 mph. No flapping, no shake, no noise. I see no way one is going to blow off.

Next time you have the top off try the front 2 panels only. This is the most enjoyable setup I’ve found so far. Little tricky getting them on the first time, just keep them level.

Scroll up a couple post if you need a visual of what I’m talking about.

 

[LoneRider]

Today marks one week since I got my Bronco. Been busy going through my punch list and knocking things out!

Today was a light day. I put on my spare tire cover and glove box organizer that arrived then finished up the Weather Tech Mud flap install I started yesterday.

I had to modify the fronts, not sure if it was WT’s fault or mine, but the ones I got were not simple swap out some fasteners. Had to cut the flaps to get in place. For the rears, the WT directions showed removing three bolts from a “cover” of sorts on the rear bumper. My bumper in that area had no bolts and no cover.

I marked it and self-tapping screws yesterday, but replaced them with better hardware today.

 

[10K_Vet]

Installed free (Ford points) Molle kit.

 

[inkd6973]

Used my RTR rewards & replaced the OEM floor liner (waste of $160) w/ the MUCH better RTR Weathertech liners. Not a fan of how the flap extends over the door sill, so will prob look to trim that area back.

i agree. the extra cost of the factory ones were a waste. not only do the seem very cheap, but with doors and tops off, i have to put front seats back to keep the rear ones from flying out.

 

[inkd6973]

Installed the @Mabett red seat covers.

im usually not a fan of red, but that POPS!!!!! GREAT CHOICE

 

[CUPRA]

I installed an 8-piece dash trim kit. It really brightens up the interior, and hopefully will protect those areas around the car that are prone to fingernail marks or wear and tear, like the AC controls, door handles and center cup holders.

 

[el_june]

Saddleman seat covers.

Thanks for the stroll down memory lane.… They look great….

 

[DaveInSA]

Saddleman seat covers.

The MGV is nice for simplying wiping clean.. but man they don't breath. And their softer than leather so... killing me in the 100+ weather down here.. wonder if these would help for summer

 

[LoneRider]

Installed free (Ford points) Molle kit.

OOOhhh, I like the Axe, need to dig mine out and mount it up!

 

[LoneRider]

Quick and easy projects today!

Put in the ”Add a fuse” tap for my 12v dash socket instead of it being hardwired to battery

Installed the under hood light strip - Cringed a little when I drilled a hole to mount the hood switch, but it had to be done.

Decided on an accent color - RED (Remember Everyone Deployed)

Bike rack and gear hammock arrived today as well!

Sponsored