What did you do TO / WITH your Bronco today? 👨🏻‍🔧🧰🚿🛠

[Tricky Dick]

Looks good, I was eyeing mine today for the cut location!

Cut off wheel or sawzall?

Cut off wheel and a flap disc to finish. I settled on 2" because it was the width of the duct tape.

Sponsored

 

[Herbie]

Cut off wheel and a flap disc to finish. I settled on 2" because it was the width of the duct tape.

Sounds pretty scientific to me.

 

[Tricky Dick]

The only accessory I’ve bought so far…

I've been trying like hell to find a very specific pair worn by Dangle on Reno 911. I believe they are Ray Ban Shooters but I can't find them with red on the bottom.

 

[Bronco21fan]

Wash and wax and took the top off for the first time. It’s awsome with the top off.

 

[604Bronco]

Looks good, I was eyeing mine today for the cut location!

Cut off wheel or sawzall?

Pretty sure he just ripped it apart with his bare hands…

 

[jkburg]

Wash and wax and took the top off for the first time. It’s awsome with the top off.

Is that the iag performance step? Also are those the Ford flaps? Did you go with the name or the horse for them?

 

[Bronco21fan]

Is that the iag performance step? Also are those the Ford flaps? Did you go with the name or the horse for them?

Those are the arch type racing steps and the gator back mud flaps that say bronco

 

[KompressorV12]

I did the spacer install today to mount my CB antenna. I went with 1” and I bet I could get away with .75” as shown from the pics. I’m planning on installing the JCR tailgate table so I didn’t run the antenna from cargo to mount yet but it’s run to the steering column ready to go. I’m going to extend my bump stops 1” but I don’t see how that adds any type of protection from the additional torque the spacer creates. I just talked to a guy who has been running a 37” tire with about 35# of additional gear on a non reinforced hinge and wheeling pretty hard. He has a height relocation bracket but nothing else yet and says he’s had no issue with the added weight. I guess I’ll just cross my fingers lol. The setup looks awesome

 

[KompressorV12]

I also finally installed my JL W7, amp, and DSP into my B&O system. Replaced the factory sub and had a new mount for DSP/AMP. The sub is a quick disconnect away from being removed if I need the space or go topless. The B&O speakers are pretty good IMO but that sub was absolutely worthless.

 

[Roll Sound]

I ordered one of these.
https://accessories.ford.com/products/keyless-entry-keypad-for-vehicles-with-factory-remote-start-2
To be installed probably inside my gas door, but TBD. Accessories.Ford has a sale going on right now, so I got the wireless keypad, with tax, shipping, and installation (programing) at Galpin for $107.73. Bam!

 

[CUPRA]

Added a brush bar and fog lights today.

*Brush bar was a collaborative design with a friend.

That brush bar looks great, I love the look of it!

 

[SevenT]

Had to put a new blade (license plate bracket) on the BronkDozer and changed the pedigree to reflect the need to dig.

=AZVJkFfQWhnMQ1yM4ttJFeNepLZI_WpCHuE_a-HI9EOJMCwklD_6353LbLo4PugSzsg1Y2G_mpa0nNkUoKTUqYaWDlFWO7YMR2QG8lINUBoBEw&__tn__=*bH-R']

 

[FATHORSE]

Added a brush bar and fog lights today.

*Brush bar was a collaborative design with a friend.

can you post pictures of how these are mounted, as well as your air port!

 

[GETSCHWIFTY]

The only accessory I’ve bought so far…

I need coffee. I saw this and said “why does that guy have a POTATO sitting on his dash?”

or maybe glasses

 

[GETSCHWIFTY]

I decided to pull the trigger….

Sponsored